Jump to content
SAU Community

Recommended Posts

BC for sure, I had them in my last R34 & put them in my current R34. Went standard 8/6 & on full soft I dont think they are much stiffer than the king springs that were on before. Full hard really is HARD!

It's not listed as a Type 1 Hooning Offence AFAIK / IIRC so it wouldn't result in an impound..although, for the paranoids:

"Dangerous operation of a motor vehicle" is a Type 1 Offence...and a very broad offence at that...open to interpretation whether an excessively low car qualifies....:P

You'd have to be pretty unlucky to get done for something like that...

Edited by fusion07

Cheers mate, does anyone know if your car is below 100m and your just randomly Encountered by police can they impound your car or is it just warning/defect?

AFAIK defect. Adjustable height coilovers are also defectable even if you are above 100mm. 100mm is whilst the car is under full load.

I have lowered my car leaving a finger width gap between the tyre & wheel arch & the body is still well over 100mm off the ground, I think it was around 150mm. I dont have a body kit on it.

My exhaust however at its lowest point is less than 100mm off the ground. Still not sure if they measure from the lowest part of the car or from a structural part.

I have lowered my car leaving a finger width gap between the tyre & wheel arch & the body is still well over 100mm off the ground, I think it was around 150mm. I dont have a body kit on it.

My exhaust however at its lowest point is less than 100mm off the ground. Still not sure if they measure from the lowest part of the car or from a structural part.

Lowest point mate. Get a bracket made to bring it up?

  • Like 1

Iirc the height adjustment threading can be spoiled/locked so it's impossible to go below 100mm, then mod plate issued. Most people wouldn't dare to spoil their expensive coilovers though so no one does it. I've been driving with bcs for 4 years now, only got pulled up once and the dude just said it's too low and drove off, mind you this is in an s15 that was slammed to kingdom come lol. My current caris much mmore sensibly set up and no attention attracted so far. If you don't plan to slam it then good chance they won't care, but it's your choice in the end.

Edit: left out an important detail never been through a roadside defect station ever. If you got stopped at one then that would be a different ballgame...

Edited by fusion07

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Given you're running a 2.8 and my 2.5 is not really like for like, I suspect there could be a bit more timing you could give it. What is the kW yield per degree you're putting through it? Here's my E85 map to give you an idea, where it was I could still get another 3~4kW per degree thrown at it.  
    • It turns out that Setrab make a fan specifically for the oil cooler which is great and I've installed it with minimal swearing. I removed my 2x 12in push fans from the front of my aircon condenser and wired them into this. My main thermo fans kick on when I use the aircon anyway and would effectively already be working as puller fans through the condensor which is infront of the rad. The push fans (understandably) didn't really do much in the config they were previously in so now they're out. Now we're on to the "Oil fan doesn't really do much either!". Yes I'll duct it next if it does nothing in heavy use which it shouldn't. But hey, the object exists and fits great and is cool. Let me have this. The car is still in the "do my fittings leak oil now? do my wheels actually rub?" phase. I did a spirited drive on them and didn't hear or feel anything. Then I got back home and noticed there were grind marks on the inside of the rims, though I couldn't see where they were touching I got out the grinder and attacked the suspects. Note: I do not know how to use a grinder. Then I realised I had dragged my new rims across my concrete driveway before I did this drive. I didn't think I had damage at that time when I briefly looked...... but remembered this occurred after I did all the angle grinding. The grinding on the wheels in some very specific spots. It's not around the whole rim for example, which lines up with dragging it across concrete more than hitting a suspension component for even 1 full rotation. So everything is currently painted and taped up and I need to test it some more to see if it really IS rubbing, but from inside the car it doesn't feel like it is. In other news I attempted to do a before and after comparison of the heads/cam upgrade thing. Dynos lie, everything is in different measurements. Here is the data from the sandown back straight. Car go faster than before. Vroom vroom.
    • Here's my base ignition. +3 correction to redline when shooting water/meth which is always on. Looking at my old ignition table, I should be able to add 1-2 degree's next time I'm on the dyno.  Let me know your thoughts. 
    • Given what I know now - same haha, but this was 12 years ago with second hand 740cc Nismo injectors in my S15 daily, I was too busy hunting elsewhere for the issue to even look at the injectors, running through some cleaner was a happy coincidence haha
    • Not a terrible idea. But if I ever had concerns that my injectors were sufficiently dirty to be causing me a problem, they would be out of the engine and onto the actual injector cleaner/testing bench.
×
×
  • Create New...