Jump to content
SAU Community

Parting Out Black R34 Sedan, Forged Neo And 400Hp Setup

slidinr32gtr
 Share

Recommended Posts

slidinr32gtr Proficient

slidinr32gtr

Posted
Posted

Parting out r34 Sedan, most parts available, except front end panels

Rb25det NEO Motor has passed inspection 170psi across the board, race series bearings, has forged pistons, adj. ex cam gear, arp head studs, metal triple layer headgasket, gates racing timing belt, head has port and polish work done. Sold as a long motor with alternator, pwr steer pump and all covers. $4000

RB25 Forward facing plenum with Siemens 630cc injectors, PFI rail and reg with gauge, billet 80mm throttle body with braided fuel lines and speed flow fittings $800

GT3037 4" inlet in very good condition, braided lines and speed flow fittings, stainless steel high mount manifold with adaptor plate for external gate, intake pipe, dump pipe $1600

NEO super spark coil packs $300

Complete manual conversion, r34 turbo box, Exedy cushion button clutch 70%, mount, x member, flywheel, pedals, master slave and lines, tailshaft and shifter, everything you need!! $1600

BC coilovers type BR for r34,front and rear, stiff springs, no leaks $700

Rear adjustable camber arms $80

Front adjustable castor arms $120

Haltech E11v2 with adapted NEO turbo manual loom with boost control solenoid and map sensor, ready for sale $900

R34 sedan rear bar VGC black $100

R34 sedan tail lights in primer $100 pair

Door cards good cond. $25ea

Dash $100

Front and rear seats good cond. $200

Centre console $100

Master cylinder and booster $50

Abs unit $100

Complete good condition boot interior and rubber seal $80

Front brakes pads and rotors vgc pads $200

All door windows, regs, switches and door shells available in black

All interior parts avail

R34 sedan side mirrors vgc In black $80 pair

​msg or PM for pics

Call/msg Johnny 0414696256
Located in runaway bay - Gold Coast

slidinr32gtr Proficient

slidinr32gtr

Posted
  • Author
Posted

Coilpacks, Haltech, Rear Bar, Tail lights, Door cards, Rear Seats, Centre console, Front brakes pads and rotors, Master cylinder and booster, Abs unit are still available, all else is sold.

slidinr32gtr Proficient

slidinr32gtr

Posted
  • Author
Posted

Sorry, Drogba brakes are sold also, but check your PM

Also still have the fascia surround for stereo, and couple of interior bits and engine bits still available

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...