Jump to content
SAU Community

Recommended Posts

I have a r33 gts-t at the moment and yes i want to make it a rb25de.

I have just found out that i have blown the head gasket, so i was just wondering if anyone would know if i can shave the head and run a thin head gasket to get the comp to at least 10:5:1 at least.

I have a powerfc wired up to my stock 25det loom already so thats why i was just gonna make this motor a DE.

thanks

Link to comment
https://www.sau.com.au/forums/topic/436421-rb25det-to-rb25de/
Share on other sites

Prob a lot easier and cheaper to sell the motor as a det and buy a neo n/a motor, I wouldn't bother getting anything machined.

It can be done though, don't see why not, there should be a lot of different thickness head gaskets available for the rb25, just don't go crazy skimming the head, don't want to take to much off.

Prob a lot easier and cheaper to sell the motor as a det and buy a neo n/a motor, I wouldn't bother getting anything machined.

It can be done though, don't see why not, there should be a lot of different thickness head gaskets available for the rb25, just don't go crazy skimming the head, don't want to take to much off.

Its just would be better for me to keeep the det as i have a pfc already wired up to it. so i save money there.

I was just worried about clearences when i shave the head and run a thinner gasket and if it would make an issue?

By the time you're done what you're planning, you could have thrown an N/A NEO6 in there for less. I've seen good RB25DE's go for $500.

Cost vs. time. Remember that machining work and parts will cost you $1k easily. Pretty sure that you'll have to change the pistons to get it to the 10:1 mark.

these threads don't get locked on sight?

TL;DR, engine is incredibly low comp for N/A use, would need to be retuned, still run like shit, and depending on the state, still be illegal. Put N/A motor in or don't drive / sell / use as track car while on P's. Conversion has been done before, with the above mentioned results.

MBS206: you mean upgrade there pal

^^what a load of misinformed dribble, 9.0 to 1 isnt by any means "incredibly low comp" , it will run fine after a retune and it will be okay to run 91 ULP and wont run like shit at all

^^what a load of misinformed dribble, 9.0 to 1 isnt by any means "incredibly low comp" , it will run fine after a retune and it will be okay to run 91 ULP and wont run like shit at all

Been done before, runs like shit.

It's not just comp that's different, but cam profiles etc etc.

^^ yes I already know that it would need a retune (ive also agreed above on that point) 9.0 to 1 is plenty high enough for a na 2.5 litre and most other engines with efficient 4 valve and dohc designs heads. .engines can be de+t and det-t...

Im not arguing that its a waste of money. . . My point is that its achevable /doable

How will different cam profiles make it run like shit?

Cam profiles are designed pending certain applications, youll be completely changing how the exhaust flows and therefrore how the head and cams will breathe.

Kind of like shoving huge overlap cams in a V8 and then bitching the car wont idle like standard...

the engine is designed as one large system, that youre f**king with. It will drive, itll also make way less power than an RB25DE from the factory. There is a reason so many people have complained about driveability after doing this exact conversion...

^^hmm google must have it wrong then because it shows the cam profiles between the r33 rb25det and r33 rb25de are the same - 240 degrees duration and 7.8 mm lift on both inlet and exhaust

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...