Jump to content
SAU Community

Recommended Posts

So I've got myself an s1 rb25de which I'm planning to bolt a turbo onto.

is it worthwhile removing these little bumps in the exhaust ports and opening them up a bit?

the head will be coming off for some block restrictors and a few other things anyway but I'm yet to decide how far to go with rebuilding it.

please excuse the noob question I'm new to this whole engine building thing.

post-85702-13899297629398_thumb.jpgpost-85702-13899297765734_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/437718-rb25-head-porting/
Share on other sites

They are "extra" material to keep the thickness around the manifold studs "correct", per Whatever spec Nissan were using at the time. You could remove most or all of the bump without negatively affecting engine strength. FWIW though, unless you are going to port the head properly, with a real power and usability target in mind, plus make sure the exhaust manifold is top notch and properly port matched, it's probably not worth your effort doing anything to it.

FWIW, grabbing a grinder and opening up ports, even just removing a little material like those bumps, is not "porting". Shaping the bowls and transitions to the valve seats and getting the velocities right to get the right cylinder fill at the target rev range and all that.....that's porting.

A standard RB25 head will flow more than enough power before you need to have any kind of head work done. What I would suggest instead of porting the head is to change the Valve Springs over to something like Supertech Valve Springs from the states. Lets you run higher Rpm before you start burning out your Hydraulic lifters....I wouldnt even change the Cams unless you are after some decent power.

They are "extra" material to keep the thickness around the manifold studs "correct", per Whatever spec Nissan were using at the time. You could remove most or all of the bump without negatively affecting engine strength. FWIW though, unless you are going to port the head properly, with a real power and usability target in mind, plus make sure the exhaust manifold is top notch and properly port matched, it's probably not worth your effort doing anything to it.

FWIW, grabbing a grinder and opening up ports, even just removing a little material like those bumps, is not "porting". Shaping the bowls and transitions to the valve seats and getting the velocities right to get the right cylinder fill at the target rev range and all that.....that's porting.

Well said.

OP - Also does depend also on aims, you've kinda not said what those are... 300rwkw, 400rwkw, 500rwkw? Street/Drag/Circuit etc.

But by the sounds of it, the above covers everything

cheers guys, looks like I'm best to leave it alone for now.

my goal for this build is around 300kw. the idea is to get a decent turbo setup running on it before switching to an rb30 bottom end built with some decent gear.

it's going into a track car so I want to use the cheap motor as a testbed to get things reliable before throwing some $$ at a decent bottom end.

the head and sump will be coming off so it'd be stupid not to at least do a basic rebuild.

I can get hold of an rb25det neo block and crank (hopefully with proper oil pump engagement) so will probably pick that up and hopefully some turbo pistons if I can get a hold of some.

Edited by zac the muss

That's all good until you work out Neos have less plateau on their piston crowns because they use smaller chambers to get the same static CR as an R33 spec RB25DET .

If you can add a Neo or same spec Stag head to your list you get as good as it gets in an RB25DET .

An R33 head on a Neo short engine will give you a low CR which isn't real good IMO .

Your call cheers A .

As far as I'm aware r33 25det cr is 9 and neo is 9.5.

I like the idea of running a neo head however I already have this motor so may as we'll use it. the r33 head is easier to work with anyway and greddy plenums bolt straight on which is a bonus.

I'm buying the neo block and crank without rods or pistons so may source some r33 turbo pistons or rebuild with the high comp DE ones.

As far as I'm aware r33 25det cr is 9 and neo is 9.5.

Yeah, but that's not the point. The compression difference is partly because of the much smaller combustion chamber, and partly because of the pistons. Put the wrong pistons with the wrong head and depending on which way you do it wrong, you'll get no compression or far too much.

If using the 33 head, then you're best off getting 33 turbo pistons, per your last line.

Edited by GTSBoy

I would not miss the opportunities to lose the hydraulic valve train and side feed injectors R33s have standard . AFAIK the CRs are the same R33 to R34 but the thing is that tightening emissions legislation forced Nissan to change the design so they could run 34s leaner and cope better with detonation .

Everyone agrees the Neo is the better spec 25DET so worth having .

Side feed injectors are a PITA , Neos went back to 14mm top feed injectors and EV14 eg ID injectors go pretty much straight in . Much more limited selection of SF injectors which aren't as good and a pain to work with .

I would be more than happy to run factory Neo rod pistons and maybe cams in a 300Kw RB25DET , they made more power std than the 33 version did so cope with the extra easily if tuned properly . The cost of improving 33 rods and pistons would more than cover the difference in price of a Neo .

Anyway your call , I know what I'd do .

A .

When my head was off when I did my 30 bottom end I hacked off those lumps. I would certainly not call it porting. I know enough about porting to know I can't do it! I had previously hacked the lumps off inside the exhaust manifold.

No back to back comparison for the "lump hack?" power gain,as i dropped a 30 under it at the same time, but I have noticed I sleep easier not worrying about different size lumps in my exhaust ports :)

Stock vs stock the Neo spec probably is a marginally better thing. But OP Zac indicated he has a R33 spec 25DE for turbocharging and track use.

If he's wanting a 3 litre, now would be the best time to make that happen.

25DE runs the light(er) duty conrods and 10:1 pistons, also the block does not come fitted with under-piston oil squirters. You might contemplate using that bottom end assembly if going straight to E85 but otherwise it's not destined for long life at 300kW target.

So really it has a good donor head, and hopefully an oil pump with lots of service life left. Perfect for use with a RB30 bottom end.

Stock 30 rods, a nice set of pistons and leave the head alone except for the VCT oil feed modification. Loads of stick, and a longish life if only run up to 6500ish rpm. :yes:

Zac if you wanted a reasonably easy turn-key engine and are prepared to play with looms etc then get a 25 Neo complete and start with that. Comments about limited value in porting are accurate because at 400rwhp there's plenty of other areas to spend the money first.

Edited by Dale FZ1

haha thanks for the input guys. seems like a lot of speculation going on here. as for ditching hydro lifters and side feeds? I'm not building a 700hp competition motor, just want a solid setup that makes enough power to have some fun on track.

clearly a neo 25det is going to be better than an r33 one but I don't have 3k to throw at a drop in motor, nor do I want one as you end up throwing away everything bar the block and head when going for decent power.

il probably end up hacking the lumps out of the exhaust ports as to me it seems completely pointless to have them there, and every little but counts right?

my main focus for this build is to get the oiling 100% sorted and reliable on track before going to a 30 bottom end, hence why I'm picking up a 25det neo block and crank to save having a collar put on the DE one, oil squirters are just a bonus.

this is a project remember, I don't need a built 30det next week. I'm quite happy to build a cheap(ish) motor and run it before going down that track. things like this can serve as a great learning curve.

Edited by zac the muss

Points well made.

Suggest to get oiling, cooling, and fuelling right, and reliability will come.

Increased rpm and boost will make issues with the first two become evident on track.

There's no issues with mix/match to get the engine you want, but you're going to need a set of pistons to give a reasonable static CR plus machining the block to make everything happy. Essentially the same work you'd do to a RB30 bottom end, hence the suggestion.

A healthy unopened 25DET or Neo 25 will give damn good results with turbo and fuel system upgrades until you're ready to spend on internal mods.

It would seem gains can be had simply from minimising those bumps in the exhaust ports rather than completely eliminating them. A bit of smoothing the sharpish edges is easily achieved without much material removed. The factory engineers decided that a bit of strength was needed in the casting to support the exhaust manifold studs, but people have reported no issues by completely removing them (when do they ever really report failures though??).

Either way, good luck you're going to have fun and it will cost a bit of time and $$ whatever you do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...