Jump to content
SAU Community

Recommended Posts

Hei guys

Realized my stagea's speedo is reading wrong but some margin. Its showing more than im actually traveling, know that traffic is usually slower than the speed limit and even when i was driving 10 over there would still be cars passing by so I took this GPS unit to check it as they are supposed to be accurate and speedo is actually showing more than gps unit. Its like 10 over at 60 and almost 20 over at 100. When speedo is showing 120 GPS says im traveling at some 100-103 kmh...

So was wondering has anyone had similar problem or is this not that common, what causes it and yeah most important how to fix it.

Link to comment
https://www.sau.com.au/forums/topic/437745-calibrating-speedo/
Share on other sites

I don't have stock wheels and tyres, but they are about the standard diameter and my speedo was also reading about 10% over.

I put on of these in the car (tapped in near the dash): http://www.jaycar.com.au/productView.asp?ID=KC5435

BTW ADRs specify a speedo must be between 0 and 10% over actual speed....how crap is that?!?

M35's are notorious for the speedo reading high, I run 235/45/18's and they still read 10k's over at 100. I hoped the Nismo cluster would be more accurate, but it wasn't.

The ecu is reading the correct speed according to my informeter, but the speedo is still out, so I just use the informeter for accurate speed measuring.

I don't have stock wheels and tyres, but they are about the standard diameter and my speedo was also reading about 10% over.

I put on of these in the car (tapped in near the dash): http://www.jaycar.com.au/productView.asp?ID=KC5435

BTW ADRs specify a speedo must be between 0 and 10% over actual speed....how crap is that?!?

Hey Duncan, was it difficult to splice in & get accurate?

My speedo is approximately 10% out as well, which is a PITA for me, with 110kph limited factory cruise control :(

My ARX runs 225/55/18 as per the placard and when the spedo is at 110 the car is actually doing 103 (per my GPS)

The V36 is out by about the same. I reckon they are built like this to slow people down.

Now I figure if i run 245 45 18 as suggested above, this will reduce my rolling diameter from 2214mm down to 2129mm and throw the spedo out by another 4 kms/hour.

I figure that if I were to run 235 55 18 then at 110 on the spedo the car would be going around 105 kms an hour.

Found some Dunlop SP Sport 235/55/18 100V LM703 for a reasonable price. Anybody running these?

245 55 18 would produce about 107 kmh at 110, an error of only 3kmh but this tyre size is likely an off road tyre and if it didn't touch my plastic guards would sound like a truck anyway!

My ARX runs 225/55/18 as per the placard and when the spedo is at 110 the car is actually doing 103 (per my GPS)

The V36 is out by about the same. I reckon they are built like this to slow people down.

Now I figure if i run 245 45 18 as suggested above, this will reduce my rolling diameter from 2214mm down to 2129mm and throw the spedo out by another 4 kms/hour.

I figure that if I were to run 235 55 18 then at 110 on the spedo the car would be going around 105 kms an hour.

Found some Dunlop SP Sport 235/55/18 100V LM703 for a reasonable price. Anybody running these?

245 55 18 would produce about 107 kmh at 110, an error of only 3kmh but this tyre size is likely an off road tyre and if it didn't touch my plastic guards would sound like a truck anyway!

You're right Chris, the tyre set up I have suggested won't solve the issue on an AR-X, as they run a larger rolling dia than the RS/RX/AXIS. Do they use a different Speedo cluster?

Using a tyre size guide, should allow you to plug in easily available tyre dimensions, and reduce the error.

Blek it was pretty straightforward to install, the wiring is actually marked on the rear of the cluster so I just intercepted the signal on the way into the dash. AFAIK in most of these cars the signal goes from gearbox to dash and then everywhere else (eg ECU and cruise control) so the dash is a good place to intercept.

The only thing to be aware of is that the link I posted is a kit, so you will need a soldering iron and some patience to put it together.

I'd normally prefer to just change tyre size (am doing that in the leaf ATM to fix the same issue) but that's expensive if you aren't already due for new tyres anyway.

You're right Chris, the tyre set up I have suggested won't solve the issue on an AR-X, as they run a larger rolling dia than the RS/RX/AXIS. Do they use a different Speedo cluster?

Using a tyre size guide, should allow you to plug in easily available tyre dimensions, and reduce the error.

I have a feeling that the cluster may be different.

when I've seen Nismo clusters on Yahoo, if I remember correctly, they state NOT ARX.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...