Jump to content
SAU Community

Recommended Posts

Well i finally got a pre-tuned chip from Toshi, basically had the fuel/boost limiter and speed limiter removed.

Here are the results, i kept things pretty tame with only 10deg advanced base timing with adj pulleys set at 2deg advanced inlet and 3deg retard on exhaust.

I think i really need to invest in a PFC to straighten out my A/F ratio and get a better power curve.

let me know what you think.

Ben.

Dynosheet2.jpg

I set the ign timing really low for two reasons.

1. i have a shit timing light i cant really trust, and didnt have time to get it sorted before the dyno.

2. i wanted it to be super conservative because i plan on taking it to WSID a few times.

I will hit the dyno again and try smooth out the midrange A/F ratio with the SAFC and maybe give it a tad more timing, just so it creeps over the magical 300rwhp mark :D

I didnt get to play with my adj pulleys unfortunately. just on the setting i listed above, so i dont know the exact difference they made.

These were on my stock injectors with 2530, the first pretuned chip with high fuel pressure saw the A/F ratio up top below 10! so they can flow a fair bit.

yeah its a bloody rocket! i love it, it pulls harder than alot of GTR's i have driven so im very pleased :)

i wonder what time ill get at WSID. i really want to get into the 12's but i think i might be dreaming a little on street tyres.

but i have some soft suspension that should help.

Hi bbenny

My chip is not only fuel/boost limiter and speed limiter removed.

Its changed

HIGT octane Fuel map.

HIGT octane Ignition time map

Fuel/Ignition timing TP scale

Some cars TTP MAX

Remove speed Rev Boost Limit

With about 4000rpm the increase is 50hp thsn std ECU.

Top end about 30HP increse.

This chip is basically for all R32 mods 044 fuel pump amd GT2530 turbo .

Price only $200 inc mods ECU and chip.

If I go to dyno with you I be able to make better map for your car .

Please give me e-mail

Im sure yours should be sweet, you have all the bits on you need.

I need a PFC to straighten out my A/F ratio and should see a better curve, might give a little more timing too just so i can say i have over 300rwhp hehe

Evan, giv ethe guys at Unigroup a call and see if they will have a play with the Wolf.They have tuned a range of ecus, and when i spoke to them about 6 months ago they hadnt tried the W0lf ver 4, but were confident it woudl be easier/better to setup then Micxrotech

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...