Jump to content
SAU Community

Recommended Posts

my missus ran it on 91 with E10 while i was overseas for a week and when i got back and drove it i could feel the engine jittery. feels like incomplete burn / running lean and the car was very underpowered, even the gear shifts seemed lazy.
so yes it can run it but it will kill your engine in the long run as the mapping and engine fuel management is intended for ron 95 or 98
i tend to fill up usually when it gets half way and il alternate sometimes 95 sometimes 98 and it runs smooth, no noises, quick response and unexpected surprises.

I ran 95 for a while when I first bought mine, I have since switched to 98 because it is only about 2cpl more than 95. I haven't noticed any difference in economy or performance.

From memory, Japan has 96RON.

E10 can be anywhere from about 91 to 96 RON depending on how long it has been sitting around.

United sell premium 100.

That's what I would be using if I wasn't tuned on their e85.

United 100 octane is garbage. its not really 100octane since it uses 10% e10 to boost the octane rating. been using it until i got my car uprev tuned and now running shell 98, much better

how do you know you get better economy if you have run 98RON 'since day one'?

Would you drink diet coke or normal coke? Normal because you know that its nicer and better than its "alternative" Edited by Howaitonaito

I always used RON98 on my 350GT in the past. Had to pump RON95 into it a couple of times when I was out of town and couldn't find a station with RON98 and noticed that the engine tends to be abit more sluggish. Anyway, the manual states that premium fuel should be used and I think I recall reading somewhere that premium fuel is basically at least RON97 or more so I always put RON98 in and have done the same for my 370GT.

Would you drink diet coke or normal coke? Normal because you know that its nicer and better than its "alternative"

Not really a relevant comparison, higher octane fuel only has a higher resistance to detonation, if you aren't detonating on 95, then 98 will do nothing for you.

I found no difference between 95 or 98 in regard to economy or performance, and I only run 98 now as I believe Japan's fuel is 96 and I prefer to er on the safe side.

Ive had two nissans before this both australian delivered cars and both went further on 98 than they did on e10.

I got told to put 98 in it when i bought it and i have. Always BP ultimate or Shell V-power (v power in a v)

Ive had two nissans before this both australian delivered cars and both went further on 98 than they did on e10.

Of course. Ethanol has a lower energy density

I have had 3 Nissans before the V35 and none of them benefited from running a higher octane fuel than they were made for.

if the V35 is indeed made for 96RON, then my preference is not to go below that, which means 98 is the best option.

Edited by sonicii

Question for those who have the ability to map / record engine parameters.

Have you seen the ECU ever actually take out timing due to the knock sensor sensing knock?

The knock map is just a secondary Table for ignition values, I don't believe it alternates between the two, but just throws a CEL and then switches over.

I've seen a motor die (nil compression) due to a bad tune knocking (electrodes off the sparkplugs). Yet the knock sensor seemed to do SFA. Unless the tuner didn't complete the knock map, or the knock map wasn't touched and had higher than tuned map values, in which we'll never know.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...