Jump to content
SAU Community

Recommended Posts

Hi all,

Sorry to make the first post a need but I'm really lost. Just picked up my first Stagea, an 03 Rx4. 1 day after getting it the main tailgate (not the glass) would not open. I found the emergency release but now it won't close completely. It latches but the dash warning and interior light stay on. I checked the two rear door related fuses in the driver kick panel but all was ok. The car does not seem to be fitted with any kind of auto close. The glass access works perfectly.

Any help/advice appreciated.

Link to comment
https://www.sau.com.au/forums/topic/438950-m35-tailgate-help/
Share on other sites

There is a relay box behind the battery, you will need to remove the covers to see it. Make sure the hole in the bottom of the battery compartment isn't blocked and filling it with water.

Dry as a bone. Has anyone else had this problem?

Yes, but did you check the fuses on the relay board?

Yes. There are two boxes behind the battery and 1 in the kick panel. All seem ok. Is there a sensor or something in the door that reels it to lock/close after you shut it?

There would be a microswitch for the button, and another in the lock mechanism to engage the auto close. I haven't played around with the lock as yet. Perhaps the wiring where it goes through the hinge may be playing up?

I hope they didn't drill through it when the child restraints were fitted.

Nothing in that tailgate is simple unfortunately.

I second that!

Did you just pull the fuses out and visually check them?

I would surgest using a multimeter or test light on each side of the fuses.

Motor is stuffed. Im in brisbane if u need help replacing

Thanks mate :) I might need to take you up on that. Beer and pizza will be provided! Is there a multimeter check I can do on the motor? I'll pull the trim off tomorrow and make sure it's not a plug undone or something easy :)

  • 3 weeks later...

Very interesting, I just got the same problem, but the glass window won't open either, checked all the fuses in the footwell, all seem ok, I checked the fuses in the engine bay as well, are any of the relays related to the tailgate?

Edited by Barras
  • 4 weeks later...
  • 6 years later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...