Jump to content
SAU Community

Recommended Posts

Hi all,

Sorry to make the first post a need but I'm really lost. Just picked up my first Stagea, an 03 Rx4. 1 day after getting it the main tailgate (not the glass) would not open. I found the emergency release but now it won't close completely. It latches but the dash warning and interior light stay on. I checked the two rear door related fuses in the driver kick panel but all was ok. The car does not seem to be fitted with any kind of auto close. The glass access works perfectly.

Any help/advice appreciated.

Link to comment
https://www.sau.com.au/forums/topic/438950-m35-tailgate-help/
Share on other sites

There is a relay box behind the battery, you will need to remove the covers to see it. Make sure the hole in the bottom of the battery compartment isn't blocked and filling it with water.

Dry as a bone. Has anyone else had this problem?

Yes, but did you check the fuses on the relay board?

Yes. There are two boxes behind the battery and 1 in the kick panel. All seem ok. Is there a sensor or something in the door that reels it to lock/close after you shut it?

There would be a microswitch for the button, and another in the lock mechanism to engage the auto close. I haven't played around with the lock as yet. Perhaps the wiring where it goes through the hinge may be playing up?

I hope they didn't drill through it when the child restraints were fitted.

Nothing in that tailgate is simple unfortunately.

I second that!

Did you just pull the fuses out and visually check them?

I would surgest using a multimeter or test light on each side of the fuses.

Motor is stuffed. Im in brisbane if u need help replacing

Thanks mate :) I might need to take you up on that. Beer and pizza will be provided! Is there a multimeter check I can do on the motor? I'll pull the trim off tomorrow and make sure it's not a plug undone or something easy :)

  • 3 weeks later...

Very interesting, I just got the same problem, but the glass window won't open either, checked all the fuses in the footwell, all seem ok, I checked the fuses in the engine bay as well, are any of the relays related to the tailgate?

Edited by Barras
  • 4 weeks later...
  • 6 years later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...