Jump to content
SAU Community

Recommended Posts

R32 coupe GTST black

BM50 90

Blue face cluster, 165,000 100

Black electric mirrors 60 ea

Clear indicators, mint condition 170

Jensen 6x9s, with the wood spacers for r32 doors 60 both

Head lights 125 ea mint condition

34 mm water temp adapter 10

Drivers window switch 60

5 bolt shafts 75 pair

Drivers seat with small rip 30

Passenger seat, excellent shape 40

A pillar covers 25

Floor carpet 40

Gab front shocks has springs on them assume lowered 70

Stock rear springs 60

Passenger door glass 20

Drivers door in good shape, with window in black 140

Seat belts, 60 each

Steering wheel centre button, 15

Lower control arms, 60 each, 100 pair

Castor arms 40 each

R33 s1 coupe Black 141,000kms

RB25DET Motor with all accessories, Loom, ECU, turbo (doesn’t look like rb25 std turbo, still Nissan though)
It was running and driving fine but you could hear a slight tapping noise from timing case, assumed idler/ tensioner pulley. Was louder with timing case off. Considering this I have priced it to go!
Also had great oil pressure and spooled up well.
$1200, cheapest complete rb25det you will find.

Complete RB25DET manual conversion.
good condition box, shifted very smooth, no noises
Flywheel, clutch, clutch master, clutch slave, clutch lines, clutch pedal, interior surround (needs boot), shifter, gear knob, tail shaft. The lot.
1450 firm
450 without box

Complete front and rear 5 stud conversion, big 4 pot brakes
Great for S chassis and NA skylines plus others!
Good pads and discs, pulled up really nicely
Hubs, brakes, front uprights, brake lines, brake pads, brake discs, everything you need.
500

Complete rear subframe with all arms only missing hubs/ brakes
with
great upgrade for r32/s13’s and such.
With diff/ shafts 450
without diff/shafts 275

Stock rear springs, great shape, 70

Stock front springs 70

Stock front and rear springs 110

Stock seats
excellent condition
- fronts 40 each
- pair of fronts 60
-full set 100

LSD differential, good condition 175

5 Bolt drive shafts $75

Drivers door, excellent paint
- 80, glass without regulator
-130, glass with regulator

Passenger door,
Complete with glass and reg 130

Door trims
50 ea

Window regs, 70 each

Floor carpet, good condition
40

Seat belts, 60 each

Interior plastics
$10-$30

Dashboard
35, vents at front bit cracked

Steering rack 100

engine cross member 90

Auto Rad, works in manuals too 70

Bare shell, Mint rear quarter panels, not rolled, awesome paint, 150

Front guards
Drivers 80 mint condition
Passenger 40 slight bend at top

Lots more r33 parts as I am stripping the car

Green label Air flow meter 60 bucks
I have about 3 or 4, good upgrade for rb26

Green label afm, not working, has been opened up and glued back closed, 15

6x Series 1 coil packs, perfect working order 80

6x Series 2 coil packs, I have never used them, so unknown 50

Rb25det coil pack loom, works fine, few chipped plugs, 40

ALL LOCATED IN ALTONA, VIC
CAN HELP WITH DELIVERY/ SHIPPING
DELIVERY REQUIRES DEPOSIT
PRICES RELATIVLY FIRM
Although, Discounts if you buy more than one thing.

SMS me for more info and photos
0433200452

I will try check this often but I forget about it

post-112497-0-91867400-1392717384_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...