Jump to content
SAU Community

Recommended Posts

Yes

http://www.r33gt-r.com/2013/07/trunk-bar-another-noticeable.html

About fitting the ECR33, just look in your boot to see if there's any predrill holes, according to the blog, there is predrilled holes on r33 gtr series3

I don't think I have those hole predrilled though but will check tomorrow. Mine is a series 1 GTS-t let alone series 3 GTR lol. If they are not pre-drilled I wonder how hard it would be to drill them in and prevent rust?

Certian models of the s15...hmm? I guess I'll post in the WTB section and look around on ebay and maybe some wreckers.

It really does sound like you need new bushes mate, if the car takes a while to settle from a corner or a bump? Creaking? This would be due to worn out bushes and shocks.

If you can't afford all of them at once, just get upper and lower control arm bushes first, swaybar bushes are cheap. And then buy some solid strut tower bars front and rear and some sway bars front and rear and new shocks front and rear.

You are most definitely right about that too. If I brake hard enough in a straight line it will actually change the alignment of my front. The steering wheel will be pointing slightly differently and the feeling of "load" on the steering wheel will be shifted.

My suspension doesn't hold alignment from the 3-4 alligments I've done either. I think 1-2mm off. There is also a vagueness to the steering. I did replace the outer tie end rods but that didn't do much. What it did do is carry the slight wobbles to the steering wheel more while driving, until about 6 months passed and I guess the new tie end rods wore out again.

I also suspect I have a bearing issue which may be wearing out components I put in faster, like the tie end rods. I took it to my mechanic to replace them ( bearings) but he wobbled the wheel around with his hands and said its fine don't waste your money so I sort of gave up (still have the bearings and some control arm bushes but places like pedders want a fortune to fit them).

Point yes probably most of the steering and suspension is a mess. But that doesn't change the fact the body also wobbles excessively after the suspension has transferred its force. Someone else in the family also has a low km R33 and thats so much tighter.

I feel like even if I change all my bushes, the body will still slop. So I though id start with some minor bracing I can get my hands, even though i know the bushes have to be done at some point too.

You guys say bracing wont do much, but I figure solid pieces of steel bolted to crucial parts of the chassis that normally flex and deform, will do something rather than nothing. It has to. I cant imagine a under-body or fender brace, or trunk brace is going to stretch or flex much , but I I can imagine that a long ass 4-5 metre long chassis un-braced will.

Edited by sonicz

You guys say bracing wont do much, but I figure solid pieces of steel bolted to crucial parts of the chassis that normally flex and deform, will do something rather than nothing. It has to. I cant imagine a under-body or fender brace, or trunk brace is going to stretch or flex much , but I I can imagine that a long ass 4-5 metre long chassis un-braced will.

Here is your error. They WON'T do what you want them to do. They WILL NOT stop the motion in the direction you need them to stop.

The fender brace will help a bit. Almost anything that goes flat across the underside of the car can only do precious f**king little. If you do not box something in in 3 dimensions, then you are adding almost no resistance to twist. And twist is what YOU want to get rid of. And all those braces are pretty much only 2D.

/engineering.

  • Like 1

I don't think I have those hole predrilled though but will check tomorrow. Mine is a series 1 GTS-t let alone series 3 GTR lol. If they are not pre-drilled I wonder how hard it would be to drill them in and prevent rust?

Certian models of the s15...hmm? I guess I'll post in the WTB section and look around on ebay and maybe some wreckers.

Judging by your post, it sounds like bracing is not your problem so i would go with what others have suggested and try something else

Tie rod ends wouldn't wear down that quickly if you have just recently replaced it, check wheel bearing or LCA bushes

As for the brace, they are standard on ALL s15s

Here is your error. They WON'T do what you want them to do. They WILL NOT stop the motion in the direction you need them to stop.

The fender brace will help a bit. Almost anything that goes flat across the underside of the car can only do precious f**king little. If you do not box something in in 3 dimensions, then you are adding almost no resistance to twist. And twist is what YOU want to get rid of. And all those braces are pretty much only 2D.

/engineering.

200% agreed. That's why I suggest a full cage. It will make that uni-body chassis have nearly .0001% flex. I understand cages are a pain in the ass for a daily but what the guy is wanting is literally the only way to achieve it. You can't achieve a stiff anti-flex chassis with braces. You might get a couple done but it will allow other areas to flex that can't handle it. I've crack front and rear glass before twisting frames up. But first thing I'd do if I had his car is take it to a body shop to get the doors realigned. Then work on stiffing.

they are standard on ALL s15s

spec-R I believe, not S?

That back-of-boot brace for the r33 gtr got a "noticeable difference" from the driver. I'm inclined to make something myself though which I don't think will cost that much and will be a bit more solid, ie, exhaust shop to bend a section of tube to run across back between mounting points, then welded to probably 3mm steel plates, bolted to chassis rails using existing 4xbolt holes as mentioned.

I could see the benefit of the front 1/4 panel triangular braces and it seems they're pretty popular/widely used so will be looking into that further too.

The B-pillar/floor brace - i get it in principle, as in using a 20?cm section of chassis rails either side joined to reduce twist, but given overall length of car/chassis rail, could see it making minimal difference.

Problem is, OP says his 33 is a lot sloppier than others he's driven (IIRC - a while since I read the full thread). If that's the case, then start with bushes and joints as they're consumable items and likely to wear out. If it isn't the bushes, and the chassis is indeed as flimsy as OP says, then we (he) have a big problem. Why is the chassis so loose? Putting in "cheap, bolt-on" braces will only partly mask the underlying problem, and will treat the symptom but not the root cause. This will never end well and I strongly suggest finding the root cause of the problem before it can be properly fixed. The bolt on braces may improve the car, but it will still be only as good as a standard car. Where's the fun in that?

/reliability engineering

that chinese place I can't remember the name of (KLS maybe?) also have r33 cages on ebay for $450ish new. No idea of fit/quality but if it was more for bracing purposes, it would be a good price.

even tho OP has said multiple time he doesn't want a frickin cage;) ...just putting it out there tho..

To the OP... if the chassis is as bad as u make it out to be... then braces may not work. a case of being "pound foolish penny wise" ?

if its really THAT bad, maybe u shd take a long hard in-depth look and figure out the problem before spending $$ on cheap braces. although cheap, they are not free and costs will add up eventually...plus... it sounds kinda unsafe to drive in if it flexes that much...

Would be cost effective to pay someone on here to have a look at your car.

They will be able to give you a run down sheet on what needs fixing and what will give you the best bang for buck and where to start.

From what you said about your wheel alignments and steering wheel shake, you REALLY NEED TO CHANGE YOUR BUSHES. :) Please just trust us on this. Start from the basics, which is to have somebody on here who knows skylines and who is a mechanic who will give you a list to get you to where you want the car to be. Once this is done, brace up.

I been reading this and heres my 2c:

Something isnt right with this car. If its actually flexing as much as described, its either been badly bent and not repaired properly, has huge mileage or been hammered over bad roads for a long period of time. Skylines are pretty robust in general and take a lot of punishment but any car has its limits. Even my 35 sedan flexes a tiny bit, but lubricating the door seals gets rid of all the noises

As suggested above, take it to a pro first before buying bracing bits. A decent panelbater would be a good place to start, chuck it up on a hoist and check the rails, floors, subframe mounting points, rust, cracks, bad repairs etc. A lot of stuff can be hidden under sound deadener

And if it really is that bad, the cost of fixing wont be worth it. Part it out and scrap the shell instead

another idea for some bracing, not hugely popular here, is sill/rail rigid foam injection. nissan did this with the infiniti Q45 back in the 90s

this stuff is meant to be good for it - http://solutions.3m.com/wps/portal/3M/en_US/Marine/Home/Products/Catalog/?PC_Z7_RJH9U5230GE3E02LECIE20S4K7000000_nid=GSLTMTP63TgsQH8HT14PGTglJ3XN7JWC1Cbl

slight hijack, but since relevant to the thread topic - after not finding the chassis braces I want, thinking I will just make my own. My understanding is, given an equal diameter and wall thickness, square tube will be stronger and flex less than round tube, is that right?

No. Two things need to be considered. When you say "equal diameter and wall thickness" you have to declare whether you mean the length of a side on your square is the same as the diameter of your round, or whether you mean "the same equivalent diameter".

If you mean the exact same dimension, then the square tube actually has more material in it (the perimeter of the square is 4.D but the perimeter of the round is only Pi.D, or about 3/4 of the square). This gives the square an advantage simply from having more material. If you mean the same equivalent diameter, then you're effectively making the square smaller so that the perimeter is the same and the amount of material is the same. Then the square should be weaker.

Square tube has corners. Corners are weak. Round tubes transfer load like an arch, all the way around.

Round cromolly tube. But it is an engineering exercise. You have to know what sort of loads will be put into the braces you want to make in order to know how heavy you have to make them. If you just guess you will most likely end up with one of the unacceptable solutions rather than falling into the narrow acceptable range. The unacceptable solutions are a) you underdo it and have a brace which deflects under the load applied or b) you overdo it and the brace is far too strong and therefore far too heavy for the benefit gained.

As most of these braces are intended to go between two (or more) points that are actually not supposed to move relative to each other and are not supposed to have loads running between them, it's a little hard to know how to go about working out what the real loads are so you can design for them. So you probably have to fall back on guessing, and so you don't end up with unacceptable solution a) which is totally useless, you need to overdo it. But whether that means that you need 1" 3mm wall tube or 1.5" 5mm wall tube (or any other size that comes to mind), I dunno.

cheers

  • Like 1

Lol...since the weight difference we're talking will be a matter of 100g, not even kilos, the weight i don't think will really become a factor. If we look at the stock strutbraces fitted front/rear as an example, i don't think it even has to be that thick-walled, so will use them as a comparitve starting point and see hos it goes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...