Jump to content
SAU Community

Poorest Rb30S Youve Done. Slappers Etc

joe blo

By joe blo,
in Engines & Forced Induction

 Share

Recommended Posts

r311111 Enthusiast

r311111

Posted
Posted

currently building one using the 300k+ block that's already in the car ( seems to be in perfect condition surprisingly so have all my 30's other then one having f**ked vss ) and if i'm feeling adventurous highly unlikely though as i am a lazy flamin mongrel who hates to lay on the floor other then to sleep, the sump will be coming off to throw some bearings in it and to bump up the oil pressure up (lack of driveway).

almost together and consists of

gt35/40 cheapie on a decent high mount and external gate

3.5' superdragger i think

ebay plenum

660cc injectors

decent cooler 2.5" piping

z32 afm ( thinking about going the r35 route thoughts ? )

decent cooler

stock 25det head tidied up and modified for vct

arp studs

stock head gasket not genuine nissan

hdi boost controller

twin tensioners side by side

ebay oil cooler

external bosch 044 with surge

alloy rad

genuine nissan thermostat

cheapie catch can to do the catching

mx7/33box with 4 puck clutch

thinking about limiting it to 6.5 k rpm with the 300k old bearings and stock oil pump or around the 7 mark if i can be arsed to change the bearings.

hoping to pound it with 20psi and am hoping for just over the 300 mark, thoughts ?

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

currently building one using the 300k+ block that's already in the car ( seems to be in perfect condition surprisingly so have all my 30's other then one having f**ked vss ) and if i'm feeling adventurous highly unlikely though as i am a lazy flamin mongrel who hates to lay on the floor other then to sleep, the sump will be coming off to throw some bearings in it and to bump up the oil pressure up (lack of driveway).

almost together and consists of

gt35/40 cheapie on a decent high mount and external gate

3.5' superdragger i think

ebay plenum

660cc injectors

decent cooler 2.5" piping

z32 afm ( thinking about going the r35 route thoughts ? )

decent cooler

stock 25det head tidied up and modified for vct

arp studs

stock head gasket not genuine nissan

hdi boost controller

twin tensioners side by side

ebay oil cooler

external bosch 044 with surge

alloy rad

genuine nissan thermostat

cheapie catch can to do the catching

mx7/33box with 4 puck clutch

thinking about limiting it to 6.5 k rpm with the 300k old bearings and stock oil pump or around the 7 mark if i can be arsed to change the bearings.

hoping to pound it with 20psi and am hoping for just over the 300 mark, thoughts ?

Sounds ok I have 314 awkw with stock unbalanced bottom end but with rings, bearings and conrod bolts limited to 7000rev/min and 1.5bar. If you don't do the bearings limit it to 6000 - 6500 and it should make near enough the same power.
r311111 Enthusiast

r311111

Posted
Posted

Kiwi rs4t that sounds like exactly what i'm hoping to do ! thanks, i have been waiting for thread like this to come up haha.

Superben, Surprisingly the motor looks brand new, the car has been serviced at a max interval of 7,000km's since new and everything that can be seen looks great.

Sir Lord Van Von Vader'ham Veteran

Sir Lord Van Von Vader'ham

Posted
Posted

Mine is a completely untouched low km bottom end bolted to a untouched head.

Rev limited to 6500rpm and 20psi putting just over 350rwkw. Only ever gets driven hard too.

Got some blow by at wtac, but that may have been from bouncing of the limiter all the down the main straight.

Cylinder psi is 130 across all 6 but im not sure I check correctly either.

Edit. Does has a 25 oil pump

  • 2 weeks later...
joe blo Experienced

joe blo

Posted
  • Author
Posted

i just pulled apart my next rb30. has pistons with 67s20 on the top. can anyone confirm if there genuine nissan rebuild ones? the part number on the pistons is the last numbers of the nissan rings but cant find part number as pistons

hopefully they are nissan ones. rebuilt between 100000 and 205000km somewhere

Duncan Grand Master

Duncan

Posted
Posted

i just pulled apart my next rb30. has pistons with 67s20 on the top. can anyone confirm if there genuine nissan rebuild ones? the part number on the pistons is the last numbers of the nissan rings but cant find part number as pistons

hopefully they are nissan ones. rebuilt between 100000 and 205000km somewhere

I'm not familiar with stock rb30 pistons, but stock rb26 pistons have 05U and a dot indicating front. So if 67S20 is the end of a Nissan part number it seems likely they are standard. And therefore standard bore as well which is good

  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...