Jump to content
SAU Community

Recommended Posts

obviously something is drawing down on the power. So yeah check all ancillary gear (interior lights etc..) and earthing straps.

I've experienced and heard a lot of people with R32 GTR's who cant leave their GTR sitting for a week or longer period of time. Some of the blame is the car alarm drawing down on the battery.

I did have the several small watch type batterys powering the m80 mongoose alarm drain after several years and had the siren part replaced.

(after ripping out the alarm and smashing it as it makes that orrible dull sound when going flat ....)

Buy a charger and put it on trickle charge whilst not driving it often.

Because if you just disconnect a battery lead terminal and if you have an alarm/imobiliser it will trigger the alarm !

The other thing I have found is that the spark plugs foul easily if it is idled for a while whilst stationary and then turned off, which makes it harder to start next time and drains the battery further while trying to crank over.

I like mine to start every time and on first turn of the key rather than 2-3 cranks. I drive it every other weekend so not often.

So replaced battery, alternator, starter, plugs', ignitor, fuel pump & filter

I understand that the OEM ECU detects the location of all cylinders on cranking. Some of the aftermarket ones look for the position of a particular piston (#1) being TDC so crank a few times on start-up

If your battery is tired this can be an issue.

Edited by Sinista32

Thanks for the feedback,

my money is on the alarm being the culprit ........

Will get it checked out, but in the meantime for <$80 buck I got myself a CTEK MX3.6 to charge the battery and then trickle charge it (my old battery charger was shite anyway......)

Cheers

The Baron

Boot light?

You can put a multimeter in amp mode in series with the battery (keys out of the ignition), then pull fuses to see what causes the drain measured on the multimeter to drop.

I just pull negative off the battery since the GTR is not a daily anymore.

Boot light?

You can put a multimeter in amp mode in series with the battery (keys out of the ignition), then pull fuses to see what causes the drain measured on the multimeter to drop.

I just pull negative off the battery since the GTR is not a daily anymore.

boot light - cunning...... will check and try the multi meter as well

Thanks

You can put a multimeter in amp mode in series with the battery (keys out of the ignition), then pull fuses to see what causes the drain measured on the multimeter to drop.

just be mindful of which scale you put your meter on. Some cheap meters which dont have fuses are only rated for so much.... or if they are fused, try not to blow them!

I'm having a similar probem, possibly due to the bottom "ring" of the battery terminal has cracked and not making good contact onto the battery post.

Called into my local Nissan dealer to suss out a new setup.

Sit down everyone -

$200

WTF?????

So I'm going to see if I can get someone to weld it shut.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...