Jump to content
SAU Community

Recommended Posts

Type 6 boards are out for R33 ECUs, far better than using a modified Z32 ECU

http://forum.nistune.com/viewtopic.php?f=9&t=2708

Nistunes are NOT rubbish, I've tuned 3x S15s with them and I have no issue with them. The software is decent too, and has the ability to overlay AFR vs. load points on the trace windows (which I find very handy).

Currently using Adaptronic too, decent ECU however the software is not as refined as others but once you get your head around it it's ok.

  • Like 1

Type 6 boards are out for R33 ECUs, far better than using a modified Z32 ECU

http://forum.nistune.com/viewtopic.php?f=9&t=2708

Nistunes are NOT rubbish, I've tuned 3x S15s with them and I have no issue with them. The software is decent too, and has the ability to overlay AFR vs. load points on the trace windows (which I find very handy).

Currently using Adaptronic too, decent ECU however the software is not as refined as others but once you get your head around it it's ok.

Are the type6 boards actually available? There was a bit of fanfare but I haven't seen anything since.

What's wrong with nistune z32 modded ecu's for r33's?

Correct me if i'm wrong, but I think you only get partial knock detection, and an issue with the TPS which results in hesitation/poor driveability. Some people experience it, some don't.

I've got a Nistune in mine, and for the price, can't really complain. Had an issue recently where one of the tracks on the circuit board (not sure if Nistune or Mainboard) burnt through, and needed to be sent back for diagnostic and repair. Only cost like $80 for the fix including postage.

My main gripe is poor driveability on tip-in and closed throttle. Can drive around it, but means I need to ride the clutch a lot at low speeds. But, I'm told this is tune related rather than Nistune. Going for turbo upgrade soon so will see if re-tune fixes it. Also asked if ECU upgrade would be worth it and was told that Nistune would be fine.

In conclusion I guess, I'm not complaining with Nistune for the money. But if I were to start again, I would strongly consider getting something like the Adaptronic straight up.

  • Like 1

I've got a Nistune in mine, and for the price, can't really complain. Had an issue recently where one of the tracks on the circuit board (not sure if Nistune or Mainboard) burnt through, and needed to be sent back for diagnostic and repair. Only cost like $80 for the fix including postage.

My main gripe is poor driveability on tip-in and closed throttle. Can drive around it, but means I need to ride the clutch a lot at low speeds. But, I'm told this is tune related rather than Nistune. Going for turbo upgrade soon so will see if re-tune fixes it. Also asked if ECU upgrade would be worth it and was told that Nistune would be fine.

In conclusion I guess, I'm not complaining with Nistune for the money. But if I were to start again, I would strongly consider getting something like the Adaptronic straight up.

Yeah after the feedback from you guys and doing some reseach about it, I think i might just save up a few pennys and buy a Power FC.

Thanks again everyone!

  • 3 months later...

...

My main gripe is poor driveability on tip-in and closed throttle. Can drive around it, but means I need to ride the clutch a lot at low speeds. But, I'm told this is tune related rather than Nistune. Going for turbo upgrade soon so will see if re-tune fixes it. Also asked if ECU upgrade would be worth it and was told that Nistune would be fine.

...

Just an update for what it's worth. After retune driveability issues are all gone. Cold start is great, and the issue I was having at part throttle has been tuned out. No limitations on Nistune there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...