Jump to content
SAU Community

Whats Wrong With My Car!?!?

bretto

By bretto,
in Engines & Forced Induction

 Share

Recommended Posts

bretto Proficient

bretto

Posted
Posted

ok guys ive got 2 things my car is doing at the moment and im just wondering if anyone else has experienced anything like this.

1. my car wont start in the morning, itll turn over and then when it does fire the revs are real low and will stall unless i hit the accelerator in and out real fast, then its fine and idles perfectly.

2. this mostly happens at night time when its cold, when i put my foot down the car boosts to max boost but just doesnt seem to go anywhere, it holds 13psi but seems to have no acceleration. i have a leak in my cooler where there are 3 bolt holes with nothing in them but i had the car tuned and it went fine, when i found the bolt holes and put bolts in them it did the same thing and i was told it was because the timing was to retarded and it wasn't reading the a/f ratios properly or something? anyway its doing the same thing now but i've taken the bolts out.

both of these things have started happening in the past month or so and ive had this cooler on for like 8 or 9 months so i dont think its because of that.

any ideas??

cheers...brett

Link to comment
https://www.sau.com.au/forums/topic/44188-whats-wrong-with-my-car/
Share on other sites
riceline Community Regular

riceline

Posted
Posted

Sounds a LOT like a CAS (Crank Angle Sensor) problem.

I know that with my R33. Untill it warms up it dosn't matter how much I try to boot it. It's not going anywhere (it makes full boost as well) . There was a thread about this a while ago and what people were finding it was MOSTLY happening when the engine was sitting at 61degrees (Mine does it till it warms up). Untill it warms up it will just keep ripping the timing out of the car. I'm using this as more of a good thing than a bad (I know its not a good thing) because it means that I have altered my driving style to allow the car to warm up properly before I try to do anything. As for the Starter problem I don't know what that could be. I would assume that it is Cas related as well.

Hope this helps

predator Grand Master

predator

Posted
Posted

mine did this recently at higher revs .. dodgy connection to O2 sensor due to SAFC connection becoming loose. From 4000rpm -> 7000rpm was dead as a donkey.. now its all fixed and screaming.

Check/swap both your O2 sensor and AFM. Its more likely to be these. If you have an aftermarket BOV - try swapping in a stocker to check that.

You can also have a big boost leak and still reach 13psi - your turbo will just be working a hell of a lot harder to get there (had this problem before also).

riceline Community Regular

riceline

Posted
Posted

I honestly belive that It would be the CAS problem because my car does the EXACT same thing as that.. With the start up I'm not sure about.

to check the cas you need to replace it/borrow one/ steal one... what ever

I Don't know how to check a CAS anyother way...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      The hydrocarbon component of E10 can be shittier, and is in fact, shittier, than that used in normal 91RON fuel. That's because the octane boost provided by the ethanol allows them to use stuff that doesn't make the grade without the help. The 1c/L saving typically available on E10 is going to be massively overridden by the increased consumption caused by the ethanol and the crappier HC (ie the HCs will be less dense, meaning that there will definitely be less energy per unit volume than for more dense HCs). That is one of the reasons why P98 will return better fuel consumption than 91 does, even with the ignition timing completely fixed. There is more energy per unit volume because the HCs used in 98 are higher density than in the lawnmower fuel.
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      No, I'd suggest that that is the checklist for pneumatic/hydraulic adjustable systems. I would say, based on my years of reading and complying with Australian Standards and similar regulations, that the narrow interpretation of Clause 3.2 b would be the preferred/expected/intended one, by the author, and those using the standard. Wishful thinking need not apply.
×
×
  • Create New...