Jump to content
SAU Community

Recommended Posts

Adam Neish is one of Sydney's most trusted engine tuners
Adam is our kind host for this SAU.NSW Event on "ECUs"...
* Saturday afternoon from 2pm
* 26th July
* 2/2 Noonan Rd Ingleburn

Eats and Drinks are graciously supplied too!

Members and Member Applicants can put their names down for this free SAU.NSW afternoon at Just Engine Management.
* Be ready to ask Qs
* Feel free to supply the name and model of your ECU for Adam to comment on; especially the following issues.

Do you want your ECU to provide more advanced functions than you currently have?
Does your ECU provide the tuning flexibility that you require?
Do you wish to change engine hardware and thus obtain the best ECU for your needs according to budget?
Do you require more diagnostics and datalogging than what your current ECU provides?
These are some of the qualms that Adam will tackle, plus your own personal ones.

Register now! If you're not yet a Member, apply now!
Limited to 40 Members.
1) DekA (E)
2) MrFijiGold (M)
3) Victory (M)
4) Clinton (M)
5) RMBLBE (M)
6) D_I_F (M)
7) MR33YO (E)
8) Terry_GT-R34 (E)
9) levinboy (E)
10 stagea pete (M)
11) Redline_GTR (E)
12) 34GeeTeeTee (VP)
13) Carmen (M)
14) twotwisted (M)
15) Tats (E)
16) luke gtr (E)
17) God_speed (M)
18) Kinks (M)
19) PRO_32 (M)
20) Calsonic14U (M)
21) Olivia (M)
22) GoldZilla (VP)
23) Owens (M)
24) Aussie_Delivered_R32_GTR (M)
25) vorse (M)
26) deongster (M)
27) NXTIME (M)
28) GOD12A (M)
29) sammi_d (M)
30) RiseofBrutality (M)
31) Moelders (M)
32) nick_7g (M)
33) Edifier (M)
34) crashdown (P)
35) BWRGTR (M)
36) TREGTR (M)
37) JoelyMoley (M)
38) Stallo (M)
39) Sovereign337 (M)
40) 533 RYC (M)


_________________________________________________________________

Reserve List
*

*

** CHECK OUT 'ADDENDA' ON PAGE 7

Please add Clinton and me to the list.

I would like some advice regarding some Power FC common problems. My R33 GTR VSPEC sometimes has the ALSD issue and I would like some advice on possible causes and solutions.




  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...