Jump to content
SAU Community

Recommended Posts

Hey

I've done searches in regards to this, but there are differing opinions and not many proper answers...

I've dumped oil plenty of times. This time though, after letting the oil drain for about an hour, I went ahead and put in fresh oil. But I've accidently overfilled...

It's 4L engine + .4L oil filter on a RB20DET. Engine has done 150k.

I put about 4L in, let it sit, had a look at the dipstick and it showed above H. Went for a small drive, let it sit again, but still sitting about 4mm too high. The dipstick shows the oil level about 4mm above max. and it just touches the letter H.

Should I drain some out?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/443919-rb20det-oil-overfill/
Share on other sites

Nah no dents, sump is all good. A fair bit of oil must have remained even after draining...

I think the best thing to do is simply get it at the correct level.

I'll see if I can drain some without undoing the plug completely, otherwise I'll dump the lot and then put it back in at the appropriate level.

Nah no dents, sump is all good. A fair bit of oil must have remained even after draining...

I think the best thing to do is simply get it at the correct level.

I'll see if I can drain some without undoing the plug completely, otherwise I'll dump the lot and then put it back in at the appropriate level.

Just to recap.

You come on here asking if the oil overfill is ok.

2 people say it is ok.

You somehow decide you should drain it.

Seems odd.

  • Like 1

Just to recap.

You come on here asking if the oil overfill is ok.

2 people say it is ok.

You somehow decide you should drain it.

Seems odd.

I don't know why you'd say that, I get asked for help all the time and it goes roughly like this:

*phone rings*

Me: "Hello"?

Caller: "Hi I need your help with X, it's doing Y"

Me: "I know what the problem is, you need to do Z"

Caller: "I don't think so, I reckon it's.............."

every. single. time.

I think people are just f*cking useless at asking for help.

To weigh in on the original conversation I fill between the H and the hump on an oil change (in an RB25 you can just dump 5L in if you have drained it on a level surface). I assume the hump is the danger zone much like there's a hump on the low side as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...