Jump to content
SAU Community

Round 1 - Sau Vic Go Kart Series


Tony Olsson
 Share

Recommended Posts

last Sunday every 2nd month, this time at ACE Karts :)

Can people who couldn't make round 1 participate in round 2?

Ace Karts is an awesome track, although last time I went there 1 of the staff was a complete asshole. Took anyone who spun out off the track straight away. Because you know, it's so hard to spin out in go karts :\

Link to comment
Share on other sites

Can people who couldn't make round 1 participate in round 2?

Yes, 100%.

We're working on a points based system for scoring the rounds, based on the results of the very wet round 1, it's still going to be anyones game! (I'm saying this because I came 8th and only got 4 points ;) )

Link to comment
Share on other sites

what was your placing?

Ok so points after round 1 are -

Quinton R - 25pts

Sam C - 18pts

John R - 15pts

Ray B - 12pts

Rhys S - 10pts

John P - 8pts

Andrew C - 6pts

Simon H - 4pts

Sean P - 2pts

Tony O - 1pts

Michael K - 0pts

Robyn R - 0pts

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share




  • Similar Content

  • Latest Posts

    • @Murray_Calavera yeah, I guessed as much, cooler temps, more boost, less knock, more timing, hello power. Unfortunately not quite within reach ATM, could upgrade my whole fuel system to support but still wouldn't have E85 to run it 😂  Anyway, I changed cams again, 260/260 poncam B and everything else the same except an EBC upgrade. Now I must say I was quite disappointed with the result as it was like running stock cams (didn't try to dial them in as they're supposed to be optimum already) but after awhile I suspected my new EBC was underperforming not to mention difficult to use. I recently swapped back my old EBC and it drives much better now, boost comes on sooner, more stable, no spikes etc, feels all quicker and faster than with stock cams. Planning to fiddle with the cam gears and see what happens but maybe skip the Dyno as I intend to revert to the HKS cams cos they really made the car come alive; low and mid end was unbelievable and it just wanted to rev to the moon, finally knew what people were raving about, RB26 really loves revs. Anyway, Dyno 03 is quite disappointing, in Dyno 02 although peak power was less and trailed off at the top, the low and mid end improvement more than made up for it.
    • @Darrel It's so tempting to say e85 is borderline magic. It cools the intake charge, so if you're flirting with the edge of the turbos compressor map it helps dramatically cool down the hot air the turbos are pumping. It is very resistant to detonation so you can crank the timing, I don't really want to say you won't be knock limited anymore.... but you probably wont be knock limited anymore lol. I wouldn't be surprised if you made 20% more power swapping to e85 (provided you have the fuel system to support them, bigger injectors maybe bigger pump etc). 
    • @Murray_Calavera nah, not available yet, they're gearing up for it but won't be available for a few years. So you reckon fuel is the main issue? When this bottom did over 600rwhp it was running big single, twin Z32 MAFs and believe it or not, e manage blue, an old school piggyback 😅 not really a fair comparison but I guess it shows how a big single differs to smallish twins.   
    • @Darrel Can you get pump e85 where you are? If you want to max out those turbos, e85 + bigger modern injectors will be the easiest way to get you there. 
    • Hi @Butters , thanks for your reply. Pump 97 BTW but yeah, I get that old tech is what it is and can't compare to modern stuff but I still believe 500 is achievable, even with these smallish twins. Their effective limit is around what, 24 psi? Intend to go single one day but then again, I'm not chasing big power and might not be worth the investment. Just wondering what if any factors are limiting my setup after a few changes. Let's call this Dyno 02. This is after R35 MAFs, 720cc injectors, DW300 FP, HKS step 2 264/264 cams.
×
×
  • Create New...