Jump to content
SAU Community

R34 Electrical Issue's

crissy

By crissy,
in General Maintenance

 Share

Recommended Posts

crissy Explorer

crissy

Posted
Posted

Hello, I have a 1998 R34 coupe and im having some weird problems.

The other week i got in to drive it and when i unlocked it problems started,

1. The tacho and speedo dont work,
2. The bell chime for door didnt chime,
3. The interior light stays on,
4. The passenger door wont lock with the button on the remote or drivers side panel.

It still starts and drives fine,
I disconnected the battery and reset the ECU which worked, but then it happened again and again now that trick only works sometimes.

Any ideas? Cheers

Link to comment
https://www.sau.com.au/forums/topic/444407-r34-electrical-issues/
Share on other sites
Deza3000 Proficient

Deza3000

Posted
Posted

I reckon you should get it checked by an automotive electrician. Sounds like brittle cables between the battery and the accessories. Could also be a shorted PCB. I had a similar problem with my r34 in regards to the power windows, ended up being brittle wiring on the drivers side, causing the passenger side window to wind down but not up. Yours is a bit more complicated, i dont think its something that will just go away.

sleptema Proficient

sleptema

Posted
Posted

Hello, I have a 1998 R34 coupe and im having some weird problems.

The other week i got in to drive it and when i unlocked it problems started,

1. The tacho and speedo dont work,

2. The bell chime for door didnt chime,

3. The interior light stays on,

4. The passenger door wont lock with the button on the remote or drivers side panel.

It still starts and drives fine,

I disconnected the battery and reset the ECU which worked, but then it happened again and again now that trick only works sometimes.

Any ideas? Cheers

Tacho + speedo: Take out the dash, check for lose plugs.

Interior light and bell chime for door could be linked (as i'm guessing with the switch on "DOOR" it stays on?, but "OFF" it turns off?) Guessing it is the switch inside the door playing up. Where that little rubber piece is.

Passenger door: Does it lock when you flick the door lock internally, like the actual switch? Does it unlock with the controls on the passenger door?

Deza3000 Proficient

Deza3000

Posted
Posted

Tacho + speedo: Take out the dash, check for lose plugs.

Interior light and bell chime for door could be linked (as i'm guessing with the switch on "DOOR" it stays on?, but "OFF" it turns off?) Guessing it is the switch inside the door playing up. Where that little rubber piece is.

Passenger door: Does it lock when you flick the door lock internally, like the actual switch? Does it unlock with the controls on the passenger door?

I was under the impression that its all just one big problem?

#@crissy

Did these arise all at the same time? Or did the car just start having more and more problems? If its the second question then id go with what sleptema suggested.

sleptema Proficient

sleptema

Posted
Posted

I was under the impression that its all just one big problem?

#@crissy

Did these arise all at the same time? Or did the car just start having more and more problems? If its the second question then id go with what sleptema suggested.

I don't think they can be related, or he would be having issues with the entire car, not just those 3-4 things. I believe the tacho and speedo gain their signals from the Engine computer, where the door lock and chime is body control computer. Tacho gets its feed from the CAS, which can in no way be related to the door locks. And if it was the ECU, I doubt the car would be running smoothly. I don't want to jump to ecu replacement when it is most likely small shit,

sleptema Proficient

sleptema

Posted
Posted (edited)

The ecu gets the speed signal from the speedo.

The tacho gets its signal from the ecu.

Weird hey.

And the ECU gets is signal from the CAS. The speedo gets its signal from the WSS yes, the ECU doesn't read the speedo, the gauge is an output from other sensors.

Sensor (input) -> ECU (processer) -> Actuator (output - in this case, gauge)

I'm saying the tacho and speedo are more than likely related, but the tacho/speedo combo isn't related to the door locks as they are on completely different circuits.

Edited by sleptema
533 RYC Proficient

533 RYC

Posted
Posted

And the ECU gets is signal from the CAS. The speedo gets its signal from the WSS yes, the ECU doesn't read the speedo, the gauge is an output from other sensors.

Sensor (input) -> ECU (processer) -> Actuator (output - in this case, gauge)

I'm saying the tacho and speedo are more than likely related, but the tacho/speedo combo isn't related to the door locks as they are on completely different circuits.

Yes, the ECU gets it signal from the CAS, the ECU drives the Tacho.

The speedo gets it's signal from the gearbox output shaft, the same place as the ECU.

The wheel speed sensors are traced back to the ABS/Attessa ECU. The only time the ENGINE ECU references WSS is during traction loss (traction control for rear wheel drive only).

  • 2 months later...
Phyco Apprentice

Phyco

Posted
Posted (edited)

Hey, Just wondering if you got anywhere with resolving this crissy? They are all connected in some way, as I have exactly the same issue. I have narrowed it down to the either the ODO/Speedo/Tacho cluster or one of the cables running into it, as generally by giving it a bit of hard tap or removing and reconnecting one of the cables from behind the cluster the issue goes away (until next time). It's funny when starting the car as you don't get the reverse beep or have the doors lock, and then all of a sudden everything happens at once, like a delayed reaction.

Edited by Phyco
Phyco Apprentice

Phyco

Posted
Posted

Narrowed mine down to a contact issue on the TK20 Brown Connector (fuel gauge side) at the back of the cluster, as it has inputs/outputs for all the affected items (Door Locks, Reverse Chime, Speedo, Tacho, Engine Temp etc) just in case that is of any help to anyone else in future!

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      Hi everyone.

      By Marek · Posted

      Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • DanMac34
      R34 Speedo not working after manual swap

      By DanMac34 · Posted

      Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • joshuaho96
      Speed Sensor replacement

      By joshuaho96 · Posted

      Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...