Jump to content
SAU Community

I'm Looking For An Engine Stand That Will Hold An Rb25

Jordy32

By Jordy32,
in General Maintenance

 Share

Recommended Posts

Jordy32 Experienced

Jordy32

Posted
Posted

Hi forum

I purchased an SR20 a few months ago and conveniently it came with an engine stand bolted to it, awesome. Now i recently purchased an RB25 engine to start working on, however I've found the engine stand i have doesn't bolt up, and honestly doesn't seem like it could support the RB's size or weight so i've put it in a tyre which is ok for pulling the manifolds and pumps off, but not great for doing proper work to it.

Does anyone have any suggestions as to a brand or particular tool shop that will sell an engine stand that meets my needs? I've called supercheap, repco and other auto stores and they have all told me that they're not sure if it will work or not.

Any help would be greatly appreciated

Cheers

Jordy32 Experienced

Jordy32

Posted
  • Author
Posted

If you are anywhere in Melbourne, you can call around to my place and take mine. It held a RB25 fine, and I really don't need it anymore.

Thanks for the offer, sadly I'm in Sydney

Thanks for the help guys, you've instilled a bit more confidence in me lol - ill go grab one on my day off

Appreciate the comments and photos!

jiffo Mentor

jiffo

Posted
Posted

Something I found with my stands, I also didn't give it a thought when buying.

A "normal" model has 2-wheels on the back and 1-wheel on a single leg out the front.

The "heavy duty" model has 2-wheels on the back and 2-legs/wheels out the front.

The heavy duty one is a bit of a nuisance when fitting up the engine as the front legs on the engine crane exactly hit the legs on the stand. The single leg stand, not a problem.

So my normal stand does everything, heaviest engine would have been a complete 2JZ with a full Rd28 probably the same weight.

Agreed. I never put any thought into it. Just buy one.

GTRPSI Mentor

GTRPSI

Posted
Posted

3 leggers work fine too.

Comes down to the gauge of steel used and welding.

I have 2 with 3 legs, one i bought 32 years ago for V8 builds, thick as anything, craps all over all the 4 legged ones ive seen that are from China.

RBs may not be heavy, but the fact they are long adds weight over the end thats not tied down, in the end there is more force than some V8s on the stand.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...