Jump to content
SAU Community

Recommended Posts

Okay had a quick look over the forum and google searched and can't really find anyone else with this same problem,

Last night I picked up my very first Nissan,

It's a r32 GTST type M

Car apparently hadn't run in 3 years

Had a quick check over the car when inspecting. Compression is a bit lower than normal but even across all 6, when we were cranking it over when first inspecting I could hear a few cylinders fire so it gave me hope and I got the car and bought it home,

So the first thing I did was plugs, pulled them out and inspected, cleaned them up and slapped them back in, checked if it was getting fuel, just pulled the line off and cranked and kept cranking until the fresh fuel I chucked in started coming through. Tried starting car and it was very very close to starting, rechecked plugs and when watching for spark noticed it was weak and arcing between the threads of plugs,

Found some brand new ford falcon plugs in garage that were same thread so just chucked them in to test it, bam the car fired up straight away, was stoked that it started up after just a few little basic checks,

BUT as you'd expect the car was running smooth exactly, would barley idle, was running richer than bill gates, fuel was pouring out the exhaust, and if you accelerated it would just sit hunting around 2500rpm, even when foot flat,

straight away I thought it would be afm, but the car has a brand new genuine Nissan afm installed just before I bought the car, came with receipt for it,

Later on a friend came over and plugged his laptop in and used some program that reads all the sensors readings, start the car up, CAS was a little out, but when warmed up was sitting on 15 (got told this is where it should be)

TPS sensor was a little bit out so we set that, still no change,

Then we noticed afm wasn't getting a reading at all, checked it was all plugged in, checked the wires around close to turbo and stuff, looked all okay, checked inside around ecu as previous owner had been messing around with something and left trim off, found a single

Black wire with a male and female end which wasn't plugged in, plugged them together and started it up and BAM the car idles and revs up fine, but it had a misfire. Went and bought the standard plugs for the car and then it idled perfectly :) was super happy ,

After all this the computer said we had code 55 from memory ,which said (no sensor faults)

So all was good,

But then I went to go take it for a drive, started it up, was fine, tapped the accelerator pedal and all of a sudden it revved up on its own to 7500rpm and then dropped back down to idle , I reversed out and went up street putting around, was running smooth just driving normal, got it up to temp and went to go boost it, as it goes to come on boost it goes no where and coughs and splutters and blows out black smoke, and then when I back off after trying and press clutch in it all of a sudden revs up to 7500 again all buy itself, stock boost guage reads it is boosting but you don't feel it because it sits coughs and spluttering.

And that's where I'm up to, I know a lot of you guys will jump and say coil packs, but I don't wanna jump to conclusions, because of the fact it revs all buy itself that high,

I still need to gap the plugs, got told to gap between 0.6-0.8

At the moment I think they are at 1.1

Need to change fuel filter

Dump all fluids and filters and put all new fresh ones in

Need to check for any leaks (vacuum and turbo piping)

If anyone's got any other ideas I could check let me know please, thank you

I'd start by putting the correct plugs in there for sure. At least one boost leak is probable. As for the free-revving, not entirely sure.

It has the correct spark plugs in it now, no change

Went over and pulled off and reinstalled all turbo pipes, shouldn't be any leakage

my fuel pump died on me slowly, caused missfiring.
new pump and filters can solve so many little issues.

7500rpm sounds like something just got stuck. throttle body cleaner would be my first purchase, clean the idle controll valve ect

also after tapping the pedal and getting 7500rpm, your damn keen to put it into reverse. could have been interesting.

Edited by GH05T

my fuel pump died on me slowly, caused missfiring.

new pump and filters can solve so many little issues.

7500rpm sounds like something just got stuck. throttle body cleaner would be my first purchase, clean the idle controll valve ect

also after tapping the pedal and getting 7500rpm, your damn keen to put it into reverse. could have been interesting.

Yeah a friend of mine told me to clean the idle control valve and shit aswell so I'll make sure I do that,

And the way I saw it, if it starts reving buy it's self I just clutch in and it won't go anywhere lol

Revving like that isnt caused by the IAC. Its more than likely the throttle got stuck. Which seriously needs to be addressed before you go much further.

And looking for leaks isnt the same as pressure testing for leaks. I strongly recommend you pressure test to find leaks. You will be surprised.

Revving like that isnt caused by the IAC. Its more than likely the throttle got stuck. Which seriously needs to be addressed before you go much further.And looking for leaks isnt the same as pressure testing for leaks. I strongly recommend you pressure test to find leaks. You will be surprised.

Throttle cable deffinatly dosnt get stuck, I've already checked that,

And okay I'll do a pressure check

Well I was going off something online, how are you meant to check them, they should be good anyway, cause it doesn't misfire at all

I was going to say with your tongue, but I don't want someone to actually try it on my suggestion. :P

If it's revving to 7.5k there is a large air leak somewhere after the throttle, and the car is running way too rich. Sounds like it may have been modified at some point. I would be replacing the AFM with a known good one and perhaps checking the injectors aren't highflowed.

I was going to say with your tongue, but I don't want someone to actually try it on my suggestion. :P

If it's revving to 7.5k there is a large air leak somewhere after the throttle, and the car is running way too rich. Sounds like it may have been modified at some point. I would be replacing the AFM with a known good one and perhaps checking the injectors aren't highflowed.

If you read the information I've supplied,

AFM has been replaced with a genuine BRAND NEW nissan one

And is reading correctly (checked with plugging in consult cable)

There's no air leaks ANYWHERE

And it just revs up buy it self only sometimes when I start it and touch throttle now,

Sometimes is rich when I first start it but clears up quickly and runs fine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...