Jump to content
SAU Community

Recommended Posts

small_zps8e8060d2.jpg

-Full 3' exhaust

-Custom built holset hrc35rs turbo

-Frontmount

-Pod filter

-Wallbro 500hp fuel pump

-G4 link ecu

Im about to go for tune and want 270 kw, should i upgrade stock injectors or is this within there range?

Also are there any mods i should be seriously looking?

-Thanks

Link to comment
https://www.sau.com.au/forums/topic/448230-my-2002-r34-gt25-t-build-injectors/
Share on other sites

ok gona get deutschworks 440 r34 high flow top feed injector, anyone able to recomend a boost guage option for r34 as my stock one wont read more then 10 psi, am i able to easily replace one into the current dash guage box?

Edited by r34lyf

Are you planning on using E85 in the future?

Modern injectors are nice to use and idle really well when you compare them to the older school injectors. I have old school 480cc Nismo's in the yellow pig but they make 275rwkw comfortably FWIW.

Read some of the injector threads and you will be in a better position to make a decision that suits you.

so stainless exhausts cause a shit engine sound, if the only stainless part is dump pipe will it cause any harmonising, or no difference? Otherwise il get a custom made dumppipe

LOL! Who told you that?

so stainless exhausts cause a shit engine sound, if the only stainless part is dump pipe will it cause any harmonising, or no difference? Otherwise il get a custom made dumppipe

Engineers, who build cars in ther spare time

1387725859359.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...