Newbie R32 Gtr Engine Upgrades Etc

[XKLABA]

Yes, that is my plan as well.

The stock motor will be slower then the one I had. That was a 236kw/350nm NA engine.

Do the fit and tune at 15psi with exhaust and cam gears and the stock 26 should make about 250rwkw and 500+nm which will easy shit on what ever NA you pulled out

[SSM]

Sweet.

Can someone school me on the Kinugawa turbos? They have three kits on Ebay that I fancy.

Tanked to local turbo man, he claimed 500+ from stock turbos with steel turbine.

[fatz]

Sweet.

Can someone school me on the Kinugawa turbos? They have three kits on Ebay that I fancy.

Tanked to local turbo man, he claimed 500+ from stock turbos with steel turbine.

your local turbo man is full o shit

and yea a tunes stock motor will wipe the floor with a na

[Hadouken]

It depends if he was taling flywheel HP. Which yeh, they probably make that

[XKLABA]

In order Small to lag, TD05-16g - TD05-18g - TD06SL2-20g, the billet Kandos seem to be very good valve per coin, I am considering the TD06 ones for my built 3.0ltr

[niZmO_Man]

Don't forget an oil cooler! One with a thermostat.

[SSM]

your local turbo man is full o shit

and yea a tunes stock motor will wipe the floor with a na

He also questioned why I bothered putting the old worn out and unreliable RB engine in a BMW instead of a M3 og M5 engine. He had used insane amount on his engine and it was never any good.

My plan is to make it reliable. A rebuild now, proper oil system, poper oil ventilation, good turbos and there will be some years before she needs to be taken care of again I hope. Not going to run insane hp anyway.

[SSM]

Go iD/ BOSCH 725 or 1000's. Much Nicer than those old wreck sard 600's

By elbows I'm assuming you mean dumps? A set of R34 GTR dumps will do.

A bit overkill with so big injectors or? Better safe than sorry though.

[Piggaz]

It is a little overkill, I agree but I can assure you the engine will idle and behave so much crisper with the newer style injectors.

[iruvyouskyrine]

As piggaz said. Injectors aren't just about their ability to flow fuel. It's about how well they work at low rpm/small pulsewidths. The newer Bosch injectors shit all over older Sards/densos etc in both departments.

[SSM]

Cheers

Did get the engine yesterday, so I have been wrenching a bit today. Tested in the car and removed the oilpan to get the diffhousing cut off.

If the result is that I just can't get room for the twins, what will be the most responsive single turbo option?

[Blackkers]

450HP on petrol... hmm easily doable. Garrett GT30 territory. That would be super responsive.

External wastegate would be nice too if you're ditching the twins

[Stixbnr32]

Ditch the n1 oil pump no matter what gears are in it.

Go Tomei/HKS/Jun every time - in that order.

Get a trust sump extension - they wing the sump so its out to the left/right.

-5's will be fine with a good set of CAMs/Gears.

I had this with standard internals - 345KW at all 4's no issues until i dropped a big end bearing due to oil pump failure.

[SSM]

I need more spesific turbo names, since I don't know shit about the number on the turbos yet

Best responsive single turbo setup will be...?

OBX manifold?

[fatz]

ah you steering wheel is on the wrong side

in that case you will get 500hp out of a stock motor

American hp is different to Australian hp

our horses are 20% smaller

[SSM]

ah you steering wheel is on the wrong side

in that case you will get 500hp out of a stock motor

American hp is different to Australian hp

our horses are 20% smaller

Nope, you are talking Norwegian Viking horses

[SSM]

Ditch the n1 oil pump no matter what gears are in it.

Go Tomei/HKS/Jun every time - in that order.

Get a trust sump extension - they wing the sump so its out to the left/right.

-5's will be fine with a good set of CAMs/Gears.

I had this with standard internals - 345KW at all 4's no issues until i dropped a big end bearing due to oil pump failure.

Tomei is best and JUN is not that good? Have a JUN pump on hand now.

[GTRPSI]

Tomie pump is externally pressure adjustable, this is the reason i only like to run them, they are only a little bit more in price to the other brand name full pumps.

There is a plug on one side, on the outside that can be removed and you can adjust the oil pressure as needed.

Other pumps have it hanging on the inside of the sump, if you want to play with it you need to get the sump off which in most cases is a engine out job.

I did my oil returns to 10.5mm in the block and head, i also added breathers to my sump and used a gated baffel 9lt sump extension and built my own tomie style windage tray to direct returning oil to the pickup area.