Jump to content
SAU Community

Recommended Posts

At a guess early twenties, and they were bankrolling it apparently...
... so many effin tyre kickers.

... one guy telling me yesterday I must have been doing at least 80km/h to do that to the car. "Wild Ride hey" One of those people that likes answering his own questions rather than listen to yours.
... another one came with a trailersaid yeah "no worries sounds good" then turned up offered me $4 grand. "Best I can do buddy"

... another turned up offered me $3 grand "yeah mate all I can afford at the moment".

I had another look under neath, front left bottom suspension arm is bent back a bit, steering and everything else looks straight, so going to swap that over and take it for a wheel alignment and get them to check it on the hoist, find out exactly what is bent and how much. Then I think Ill fix it and flog it for $18 grand. With 100 octane and 300 kw. :)

  • Like 1

of topic, but where did you find 100 octane? never seen it before.
If i was you i'd fix it myself and either keep it or then sell it for above 10k. it's 300 kw so it's worth saving it.

of topic, but where did you find 100 octane? never seen it before.

If i was you i'd fix it myself and either keep it or then sell it for above 10k. it's 300 kw so it's worth saving it.

United has it in Canberra, so does Shell I think.

I sold my other GTR, dont have the $ to keep it maintained, but Ill be buggered if Ill give this one away for peanuts.

Yes insured through Shannons, and bought back, its not on the register at all. Hhad a panel beater look at it yesterday, he reckons front tie rod is bent (they are apparently soft), no front chassis damage, unsure about the cradle but probably no damage, there's a small dent in the rear sill chassis rail but is not a fold, so will pull out. A right rear GTR cut, drivers pillar, and new roof, door trim/window, and front side windows. Rear cradle looks OK as well but cant tell until you get it on a hoist and measure it properly.

I didnt know you can buy back from insurance company and the vehicle doesnt get recorded as a write-off-stat or repairable. If true, am interested pending your suspension checks you stated you are going to get done.

Edited by Nozila

Insurance companies can "write off" a car financially, meaning it's not worth the money fixing it.

Doesn't mean it's unable to be repaired or recorded on a register, or necessarily has to be fixed. A mate had a vp commodore smashed into. Insurance wrote it off financially, he got the money and kept driving, just kicked out the dent (rear quarter)

This looks like a potentially good buy.

Good luck with the sale.

Of course you can, the whole "Write off" register was developed to stop poor schmucks from buying cars that had been poorly repaired.

You can repair anything with enough time, parts and most importantly MONEY.
I will get it certified by the local panelbeaters though, so there is a certificate that it was done properly and not bogged up.

Yes it would have been a good buy, but thankfully I managed to beg enough money to pay my rates, so I'm going to fix it and sell it for $18k instead.
Interior chassis is undamaged, slight dent from the side impact in a webbing area, easy fix with fingers
Parts needed so far:

- right rear bottom suspension mount
- right front bottom suspension mount
- right front steering arm (part of rack, only has a slight bow, rather replace it than straighten it and have issues later)
- rear interior plastic window trim drivers and passengers side (clips are buggered badly both sides, more age than damage).
- drivers B pillar top section needs a tug out 7mm, rest is good
- drivers interior top door frame munted, need replacing.
It looks like roof section will mostly come back, its being held under tension by the A pillar.

Now if the effin thing would just start, no faults on ECU, everything looks OK, cranks evenly, compression is good, start ya bastard does nothing so maybe the coil control unit has packed up?

- drivers A pillar down to chassis is munted obviously).

not sure if you can insure after that point though?

  • Like 1

I didnt know you can buy back from insurance company and the vehicle doesnt get recorded as a write-off-stat or repairable. If true, am interested pending your suspension checks you stated you are going to get done.

Cars older than 15 years don't have to be reported on. I had a similar situation with my 180b. I negotiated a deal with the insurance company, car was "written off", got a fat cheque and kept the car and continued driving it. Vicroads was not informed.

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...