Jump to content
SAU Community

Help Plz Brake Noise

maso26
 Share

Recommended Posts

AMR33 Mentor

AMR33

Posted
Posted (edited)

were the pads you tried OEM or aftermarket?

sometimes aftermarket pads do not sit the exact way OEM pads would and leave a bit of a gap and may be sitting a bit loose in the caliper. Go supercheap and buy some brake squeal stop or whatever its called. Its a red paste you spread on the outside of the pads and once it drys, it becomes rubbery and helps bridge small gaps you may have between the pad and caliper.

Edited by Abdul11
maso26 Contributor

maso26

Posted
  • Author
Posted

na i dont iv'e been trying to buy some can't seem to find anyone who sell them iv'e always put FB status's on drift sales and other pages, i went to my local nissan dealer my they said you have to go to a bigger dealership like doncaster Nissan or some shit also i took my caliper off today and i saw my rubber on my brake piston is cracked and exposes the piston a little do you reckon that could be a reason, i might try a full caliper rebuild

Ben C34 Grand Master

Ben C34

Posted
Posted

haha ill do a full rebuild next week and ill see how it goes, does anyone know where do get some brake shims honestly iv'e been looking over two month's cant seem anyone who have any

A wrecker.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...