Jump to content
SAU Community

Recommended Posts

T67 ebay version is a 25G on a L2 turbine. 25G compressor is good enough for 430rwkws while the L2 turbine is good for 370rwkws. In combination the maximum I'm seeing was about 370rwkws on 23psi, factory cams. they don't last long at that boost level either. Commonly seen Greddy T67 consists of 25G with TD06H turbine is fine for both longevity and power making, but it does cost responds.

In addition, we build some alternatives based on the 10cm L2 turbines that makes the same power as the L2 based 25Gs, that are more responsive, last longer at similar cost. Check out SL20.5 and SLSS2 on Rb25det dyno section.

well ive run into a bit of drama with a noise, not sure if the cams have caused it or bottom end, but apparently bottom end knocks dont go away once warm like this does. plus my vct gear is on its last legs.

but yes still going strong when i do drive it.

Edited by methz

I had a Kando T67 with a TD06L2 exhaust wheel in 10cm. It made 368rwkws on 24psi. First one lasted 4 month and the replacement lasted 3 month. They no longer reply to my emails now. Photo of the last one:

front.jpg

inhousing.jpg

rear.jpg

Edited by petero'nell

T67 ebay version is a 25G on a L2 turbine. 25G compressor is good enough for 430rwkws while the L2 turbine is good for 370rwkws. In combination the maximum I'm seeing was about 370rwkws on 23psi, factory cams. they don't last long at that boost level either. Commonly seen Greddy T67 consists of 25G with TD06H turbine is fine for both longevity and power making, but it does cost responds.

In addition, we build some alternatives based on the 10cm L2 turbines that makes the same power as the L2 based 25Gs, that are more responsive, last longer at similar cost. Check out SL20.5 and SLSS2 on Rb25det dyno section.

Greddy differentiate their T67-25G and TD06H-25G for that reason. A TD06H-25G is actually bigger than a T67 in Greddy speak. They share the same compressor side but on the hot side the T67 uses the smaller L2 turbine.

If you have seen a Greddy turbo with a 25G compressor and the TD06H turbine then it is a TD06H-25G...not a T67-25G or what is referred to commonly as the T67.

Cant speak to the reliability of Kando turbos but it does seem possible that the later ones are a little more grenade like than the earlier ones and definitely Trust turbos. Trust turbos just keep on keeping on. Though these days with E85 and boost over 25psi I do wonder whether the would be as happy in the 25-30psi range as they were in the 20-25psi range

  • 3 weeks later...
  • 8 months later...
  • 1 year later...
On ‎9‎/‎12‎/‎2014 at 0:36 PM, hypergear said:

T67 ebay version is a 25G on a L2 turbine. 25G compressor is good enough for 430rwkws while the L2 turbine is good for 370rwkws. In combination the maximum I'm seeing was about 370rwkws on 23psi, factory cams. they don't last long at that boost level either. Commonly seen Greddy T67 consists of 25G with TD06H turbine is fine for both longevity and power making, but it does cost responds.

In addition, we build some alternatives based on the 10cm L2 turbines that makes the same power as the L2 based 25Gs, that are more responsive, last longer at similar cost. Check out SL20.5 and SLSS2 on Rb25det dyno section.

Is there quite a few Kando T67s that have failed at around 23psi on a 25?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...