Jump to content
SAU Community

Recommended Posts

T67 ebay version is a 25G on a L2 turbine. 25G compressor is good enough for 430rwkws while the L2 turbine is good for 370rwkws. In combination the maximum I'm seeing was about 370rwkws on 23psi, factory cams. they don't last long at that boost level either. Commonly seen Greddy T67 consists of 25G with TD06H turbine is fine for both longevity and power making, but it does cost responds.

In addition, we build some alternatives based on the 10cm L2 turbines that makes the same power as the L2 based 25Gs, that are more responsive, last longer at similar cost. Check out SL20.5 and SLSS2 on Rb25det dyno section.

well ive run into a bit of drama with a noise, not sure if the cams have caused it or bottom end, but apparently bottom end knocks dont go away once warm like this does. plus my vct gear is on its last legs.

but yes still going strong when i do drive it.

Edited by methz

I had a Kando T67 with a TD06L2 exhaust wheel in 10cm. It made 368rwkws on 24psi. First one lasted 4 month and the replacement lasted 3 month. They no longer reply to my emails now. Photo of the last one:

front.jpg

inhousing.jpg

rear.jpg

Edited by petero'nell

T67 ebay version is a 25G on a L2 turbine. 25G compressor is good enough for 430rwkws while the L2 turbine is good for 370rwkws. In combination the maximum I'm seeing was about 370rwkws on 23psi, factory cams. they don't last long at that boost level either. Commonly seen Greddy T67 consists of 25G with TD06H turbine is fine for both longevity and power making, but it does cost responds.

In addition, we build some alternatives based on the 10cm L2 turbines that makes the same power as the L2 based 25Gs, that are more responsive, last longer at similar cost. Check out SL20.5 and SLSS2 on Rb25det dyno section.

Greddy differentiate their T67-25G and TD06H-25G for that reason. A TD06H-25G is actually bigger than a T67 in Greddy speak. They share the same compressor side but on the hot side the T67 uses the smaller L2 turbine.

If you have seen a Greddy turbo with a 25G compressor and the TD06H turbine then it is a TD06H-25G...not a T67-25G or what is referred to commonly as the T67.

Cant speak to the reliability of Kando turbos but it does seem possible that the later ones are a little more grenade like than the earlier ones and definitely Trust turbos. Trust turbos just keep on keeping on. Though these days with E85 and boost over 25psi I do wonder whether the would be as happy in the 25-30psi range as they were in the 20-25psi range

  • 3 weeks later...
  • 8 months later...
  • 1 year later...
On ‎9‎/‎12‎/‎2014 at 0:36 PM, hypergear said:

T67 ebay version is a 25G on a L2 turbine. 25G compressor is good enough for 430rwkws while the L2 turbine is good for 370rwkws. In combination the maximum I'm seeing was about 370rwkws on 23psi, factory cams. they don't last long at that boost level either. Commonly seen Greddy T67 consists of 25G with TD06H turbine is fine for both longevity and power making, but it does cost responds.

In addition, we build some alternatives based on the 10cm L2 turbines that makes the same power as the L2 based 25Gs, that are more responsive, last longer at similar cost. Check out SL20.5 and SLSS2 on Rb25det dyno section.

Is there quite a few Kando T67s that have failed at around 23psi on a 25?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...