Jump to content
SAU Community

Recommended Posts

hey guys I got a rb30 patrol with 33inch tyres I have converted it to efi and im having economy issues

im only getting 120khm to 40ltrs of fuel its got a new afm and new air filter its running nicely any ideas why its using so much I was getting 550 -600 out of it when it was carby

Link to comment
https://www.sau.com.au/forums/topic/452244-rb30-patrol-fuel-consumption-issues/
Share on other sites

Can be checked with a multi meter and best to check on the ecu pin. Google what to expect when checking it.

That's extremely bad economy so I wouldn't think just o2 could make it so bad.

Have you checked the ignition timing?

Would be good to see of the ecu has any fault codes, but that would assume you have wires it all up to the consult port or engine check light.

So what exactly did you do to convert to efi? ECU? Fuel pump? Fuel pressure?

Does it seem to drive any differently?

(highly unlikely the O2 sensor will have ANY effect, especially if you are in a city.)

So what exactly did you do to convert to efi? ECU? Fuel pump? Fuel pressure?

Does it seem to drive any differently?

(highly unlikely the O2 sensor will have ANY effect, especially if you are in a city.)

That's a funny question. I would love to see how someone could convert to edit without changing the pump and regulator. And ecu.

The O2 sensor has a big affect on consumption. Google it.

Not big enough to explain this but easily 15 percent.

Edited by Ben C34

Just for Ben:

What ECU is being used? Factory? Chipped? Aftermarket?

What fuel pump?

What is the fuel pressure?

And the O2 sensor will have absolutely minimal EFFECT on fuel consumption in city, ie stop / start, driving. The O2 sensor only contributes when in closed loop, ie constant throttle, driving.

The O2 sensor allows the ecu to control fuel.mixtures in closed loop at low load as you know.

It also is used by the ecu for long term fuel trim , which is applied when in open loop. When the O2 sensor isn't working correctly the ecu runs as rich as it can (has been programmed for ) as a safety measure. Therefore regardless of what style driving you do, a non functioning o2 sensor will increase fuel usage.

Have you check water temp sensor?

3km/L seems very excessive. Is there a lot of black smoke coming out the exhaust while driving? I know you said it's driving nicely but I can't see a car driving too nicely when it's using that much fuel.

One thing I'm having trouble understanding is how you were getting 13.75-15km/L on an engine moving a 2T car in the first place.

Edited by Dobz
  • Like 1

From my previous experience with weirdly high fuel consumption, i found the purge control and fuel return line plumbed up wrong, check that your fuel return is on the pump properly or else the intake manifold will suck up fuel straight from the tank under vacuum from the manifold, in my case my consumption was 20L/100km and came down to 12L/100km which is quite a difference, also consider the fuel reg which can leak raw fuel into the intake.... You will want to sort this out cause it will lead to premature wear on the cylinders, and could result in piston slap from having the cylinders constantly being washed and running dry...

Edited by AngryRB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...