Jump to content
SAU Community

Recommended Posts

Hi guys, Need guards rolled on Monday does anybody know someone who is good at doing 32s and is patient because it's been painted and I'm not keen on possible paint flaking and so forth. Just want a clean job while keeping front inner guard plastic in also

Anyone ?

Link to comment
https://www.sau.com.au/forums/topic/452499-my-32-gtr-need-guards-rolled/
Share on other sites

He seems like the only guy around!

He stuffed me around time wise said yeah then said nah cant do it now. plus had an attitude when I spoke to him?

he's a pain in the ass n he won't get my money

he believes his gods gift I think.

I'd use a hammer before using that guy.

Anyone else

He seems like the only guy around!

He stuffed me around time wise said yeah then said nah cant do it now. plus had an attitude when I spoke to him?

he's a pain in the ass n he won't get my money

he believes his gods gift I think.

I'd use a hammer before using that guy.

Anyone else

Tis good that you supply feedback albeit about attitude and willingness to serve.

Any feedback about workmanship?

The other worry is cracking due to previous hidden repairs.

Many GTR's have bog in the rear guards.

Our panel beater cut our lips to play it safe.

You can seal the cut from under after its been done.

The other worry is cracking due to previous hidden repairs.

Many GTR's have bog in the rear guards.

Our panel beater cut our lips to play it safe.

You can seal the cut from under after its been done.

that sounds like the go but unfortunately my car i purchased it already painted so i'm not sure what's under there but it looks a very clean job bit scared about doing it myself i'm sure there's a mac to it

You can cut the lip with the panel painted, its not right up to the edge but near it, even rolled guards are usually not right up to the edge.

Any burning of paint on the edge is still from under and can be sealed.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...