Jump to content
SAU Community

Recommended Posts

I am parting out my r32 sedan, most parts available, but not the motor. Located in Newcastle, not going to list everything write a reply, or SMS 0414545301 for a quicker response. post-132714-14212066727002_thumb.jpg this is the car, so if you wanted something from drivers front, you out of luck.

Link to comment
https://www.sau.com.au/forums/topic/452700-wrecking-r32-gtst-sedan4-door/
Share on other sites

post-132714-14212324039971_thumb.jpg. Speedo surround $30

post-132714-14212324566616_thumb.jpg. Drivers window switch $20

post-132714-14212325145468_thumb.jpg. Centre dash surround $20

post-132714-14212325847784_thumb.jpgpost-132714-14212326036196_thumb.jpg. Seats $30 eachpost-132714-1421232647875_thumb.jpgpost-132714-14212326693046_thumb.jpgpost-132714-14212326947516_thumb.jpg. Doors including glass & window motors $80 each not including inside trim, post-132714-14212328109595_thumb.jpg. Rear bar $60

Tail lights $30 each

Boot $50 post-132714-14212329130923_thumb.jpg. Plenty more parts, car was complete at time of accident. Will post more photos as the parts come off.

Looking for:

- Centre Air Con Vent

- Drivers side pillar plastic panel (front section where tachos usually go)

- Passenger side rear pillar plastic panel (between back window and back door)

- Passenger side front inicator (providing its semi amber)

Poor little car :(

Edited by aussiebooster

Aircon vent has some broken bars on one side, other side is good.

post-132714-14213025951243_thumb.jpg. A pillar trim has cracks and a screw hole but sits in there how it should

post-132714-14213026834585_thumb.jpg. C pillar trim was in process of being fixed, has been coated with fibreglass, so it's very strong now, just needs a sanding then re covering. post-132714-1421302804236_thumb.jpgpost-132714-14213028263623_thumb.jpg I trial fitted them as is, & they fit good, just need to be sanded back abit, as adding the vinyl will make them to thick. $10 each or If you want all of it $20

  • Like 1

Drivers sun visor and driver/passenger kick panels with flare holder?

post-132714-14219163549118_thumb.jpgpost-132714-1421916373967_thumb.jpg. Drivers kick panel has a hole & missing insulation. Both have minors scratches. Passenger $15, drivers $10.post-132714-14219165149463_thumb.jpg. .jpg]

Drivers sunvisor, needs a clean $10

post-132714-14219165564255_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...