Jump to content
SAU Community

Recommended Posts

I am parting out my r32 sedan, most parts available, but not the motor. Located in Newcastle, not going to list everything write a reply, or SMS 0414545301 for a quicker response. post-132714-14212066727002_thumb.jpg this is the car, so if you wanted something from drivers front, you out of luck.

Link to comment
https://www.sau.com.au/forums/topic/452700-wrecking-r32-gtst-sedan4-door/
Share on other sites

post-132714-14212324039971_thumb.jpg. Speedo surround $30

post-132714-14212324566616_thumb.jpg. Drivers window switch $20

post-132714-14212325145468_thumb.jpg. Centre dash surround $20

post-132714-14212325847784_thumb.jpgpost-132714-14212326036196_thumb.jpg. Seats $30 eachpost-132714-1421232647875_thumb.jpgpost-132714-14212326693046_thumb.jpgpost-132714-14212326947516_thumb.jpg. Doors including glass & window motors $80 each not including inside trim, post-132714-14212328109595_thumb.jpg. Rear bar $60

Tail lights $30 each

Boot $50 post-132714-14212329130923_thumb.jpg. Plenty more parts, car was complete at time of accident. Will post more photos as the parts come off.

Looking for:

- Centre Air Con Vent

- Drivers side pillar plastic panel (front section where tachos usually go)

- Passenger side rear pillar plastic panel (between back window and back door)

- Passenger side front inicator (providing its semi amber)

Poor little car :(

Edited by aussiebooster

Aircon vent has some broken bars on one side, other side is good.

post-132714-14213025951243_thumb.jpg. A pillar trim has cracks and a screw hole but sits in there how it should

post-132714-14213026834585_thumb.jpg. C pillar trim was in process of being fixed, has been coated with fibreglass, so it's very strong now, just needs a sanding then re covering. post-132714-1421302804236_thumb.jpgpost-132714-14213028263623_thumb.jpg I trial fitted them as is, & they fit good, just need to be sanded back abit, as adding the vinyl will make them to thick. $10 each or If you want all of it $20

  • Like 1

Drivers sun visor and driver/passenger kick panels with flare holder?

post-132714-14219163549118_thumb.jpgpost-132714-1421916373967_thumb.jpg. Drivers kick panel has a hole & missing insulation. Both have minors scratches. Passenger $15, drivers $10.post-132714-14219165149463_thumb.jpg. .jpg]

Drivers sunvisor, needs a clean $10

post-132714-14219165564255_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...