Jump to content
SAU Community

Recommended Posts

I am parting out my r32 sedan, most parts available, but not the motor. Located in Newcastle, not going to list everything write a reply, or SMS 0414545301 for a quicker response. post-132714-14212066727002_thumb.jpg this is the car, so if you wanted something from drivers front, you out of luck.

Link to comment
https://www.sau.com.au/forums/topic/452700-wrecking-r32-gtst-sedan4-door/
Share on other sites

post-132714-14212324039971_thumb.jpg. Speedo surround $30

post-132714-14212324566616_thumb.jpg. Drivers window switch $20

post-132714-14212325145468_thumb.jpg. Centre dash surround $20

post-132714-14212325847784_thumb.jpgpost-132714-14212326036196_thumb.jpg. Seats $30 eachpost-132714-1421232647875_thumb.jpgpost-132714-14212326693046_thumb.jpgpost-132714-14212326947516_thumb.jpg. Doors including glass & window motors $80 each not including inside trim, post-132714-14212328109595_thumb.jpg. Rear bar $60

Tail lights $30 each

Boot $50 post-132714-14212329130923_thumb.jpg. Plenty more parts, car was complete at time of accident. Will post more photos as the parts come off.

Looking for:

- Centre Air Con Vent

- Drivers side pillar plastic panel (front section where tachos usually go)

- Passenger side rear pillar plastic panel (between back window and back door)

- Passenger side front inicator (providing its semi amber)

Poor little car :(

Edited by aussiebooster

Aircon vent has some broken bars on one side, other side is good.

post-132714-14213025951243_thumb.jpg. A pillar trim has cracks and a screw hole but sits in there how it should

post-132714-14213026834585_thumb.jpg. C pillar trim was in process of being fixed, has been coated with fibreglass, so it's very strong now, just needs a sanding then re covering. post-132714-1421302804236_thumb.jpgpost-132714-14213028263623_thumb.jpg I trial fitted them as is, & they fit good, just need to be sanded back abit, as adding the vinyl will make them to thick. $10 each or If you want all of it $20

  • Like 1

Drivers sun visor and driver/passenger kick panels with flare holder?

post-132714-14219163549118_thumb.jpgpost-132714-1421916373967_thumb.jpg. Drivers kick panel has a hole & missing insulation. Both have minors scratches. Passenger $15, drivers $10.post-132714-14219165149463_thumb.jpg. .jpg]

Drivers sunvisor, needs a clean $10

post-132714-14219165564255_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...