Jump to content
SAU Community

Recommended Posts

Hi Guys,

I want to install a LC1 wideband into my R32 GTST, and was after some advice on the best way to do it. Should I install it in the NB factory location and wire up the factory plug for the power, NB emulation, ground ? Also where is the best location to route the cable into the cabin. Any advice would be appreciated

Thanks

Link to comment
https://www.sau.com.au/forums/topic/453873-wideband-install-advice/
Share on other sites

What do the instructions that came with the kit say? My AEM kit gave specific instructions for where to mount it, something like at least 1m away from the turbine outlet and at least a 10 degree above the vertical.

I think it does work in the stock location, but it isn't the best spot to put it. I can see how it might be an issue, with the extra heat that would be right at the exit. AFR's will be the same the length of the exhaust pipe, its the delay in having the sensor at the back compared to at the front, obviously it does take a little bit of time for the exhaust gas to get to the end of the exhaust pipe

I would look at the instructions and see what it says. If you mount it in a different location then you can run it through the gearshifter hole, this is where I ran mine (its mounted about half a metre pre-cat from memory)

It would really be helpful to see some sort of wiring diagram that innovate give with the sensor. I could look it up and see, but I can't really be bothered right now. I'm hoping you have at least had a look at what it says before making this thread.......?

I looked at the manual just now. Read that, the answer to all your questions are there amazingly......

Turbocharged Vehicles:

Install the bung downstream from the turbo before the catalytic converter. The high exhaust pressure before the turbo interferes with the lambda measurement and the high exhaust temperatures encountered there can damage the sensor.

The factory NB is in the down pipe that is coming off the turbo, I could get a bung put in I suppose and run it up through the gearshifter hole and power it via cigarette lighter? What 12V source and ground did you tap into?

Just thought I could replace the NB and use the LC1 NB emulation , but thats imperative

I installed one on my stagea just before the cat, then ran the cable up through a hole in the transmission tunnel (drilled a hole).

The "proper" way to power it is to wire a relay to the battery, then activate the relay via a 12v source when the key is in the on position. This ensures you know how much current is flowing through a circuit, whereas if you draw 3 amps through an existing circuit, that may blow the fuse, create a voltage drop etc

For me, the cigarette lighter turns on with accessories, so not desirable. Test yours with a multimeter to be sure.

A workshop manual will have wiring diagrams which you can use to find an "ON" position 12v source.

Always mount it away from the turbo outlet, as prolong heat exposure will kill the sensor. Just get an exhaust shop to weld the bung before the cat but after the turbo.

I ran my cabling up through the stock EGT probe for the dashlight.

I just used the ignition source under the steering column for all wideband installs I do. Works a treat, just use a clean ground, preferably on the cars body instead of a shared ground.

I just used the ignition source under the steering column for all wideband installs I do. Works a treat, just use a clean ground, preferably on the cars body instead of a shared ground.

Thanks mate , is it run from one of the fuses? Or another location? First time I have installed one. Wouldn't have a pic? :P

Thanks mate , is it run from one of the fuses? Or another location? First time I have installed one. Wouldn't have a pic? :P

straight off the thick cable off the ignition barrel into a 5 amp fuse :)

I might have a photo at home.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...