Jump to content
SAU Community

Recommended Posts

hahaa...

The Mazda 2 with $9K damage will have it's roof replaced.

Is this car worth keeping afterwards?

I suppose it depends on how it's performed but have you heard of pros and cons?

Terry, when Shell's car got hit a few years ago; LMSR replaced the entire RHS of the car.

Both doors, B pillar, cant rail, sill panel, rear quarter/C pillar new rhsr strut, hub and rim.

There was nothing on the entire side of the car.

Every panel Bill removed, the straighter the shell became. Set up on their table the shell was perfect.

Rebuilt, they reckoned that it was better than it was brand new.

12 months later; I'd defy anyone to pick the repairs.

More than 6 years down the track we haven't had a single issue with the repairs or even with the way the car wheel aligns.

Done right; it will be perfect.

  • Like 1

"Done right" being the key words.....

There's the expectation that you would only be utilising a trusted repairer for a job like this.

I'd no more trust a dodgy panel repairer, than I would a dodgy mechanic with any of my cars.

Over the years I've cultivated a healthy relationship with my repairer, and that's why I had no hesitation with them undertaking such an extensive repair.

Shell was very doubtful that they could repair it completely, so he invited Shell & I down to see the car when it was completely stripped of the damaged structure.

He then hung all the structural members on the shell in front of her to demonstrate how straight the body was.

Picked up Volvo XC60 this arvo.

Undamaged paint: tick

All dents gone: tick

New tailgate light lens: tick

Aluminium mouldings: tick

Rubber momouldings: I rejected a front roof moulding. It has two dents and the edge is lifting. Rephotographed and reported to the insurance company.

Other: Offside blinker didn't work and offside rear parking light didn't work. It was just a detached loom.

At least the most critical parts have been done well; the rest, while a bit disappointing, isn't the end of the world.

Hope the get the finer details sorted quickly Tez.

When does the Mazda go in?




  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...