Jump to content
SAU Community

Recommended Posts

I am moving overseas at the end of this month and I am going to keep my Skyline… That thing is my baby and I have spent to much money and time on it for some P plater to buy it and wrap it around a pole…


Just wondering what I would need to do to a car before putting it in storage for possibly 12 months or more?


I have some friends to look after it in their garage but problem is they are not car people and I know they will not want to turn it over as it will bother their neighbours.


Any recommendations of what I can do to it to avoid problems when I return and put it back on the road?


Should I drain all the fuel?

If it is in a garage would you recommend having a cover over it?

Should I keep it on jack stands?


Any help is appreciated thanks!

It wouldn't hurt to do an oil change and a flush with fresh coolant.

I'd disconnect the battery, and buy 4 cheap bits of carpet to throw under the tyres.

Agree with Ants; throw a car cover over it while you're there.

can't see why you'd want to drain the fuel either....if the lines are empty they and the various o rings etc are more likely to perish.

one thing I would suggest is a low tank of fuel that you fill fresh when your are running again, and of course an oil change when you get back as well.

I had my car in a dry shed for nearly 3 years.

Took the battery out ignored the fuel level threw a few doonas over it and sat it on bricks so the tyres didnt flat spot.

When I first started it, took about 5 tries on the strater and it went. Changed the oil and radiator fluids, filled the tank with premium and drove it.

Done 5,000k since and no hiccups caused by sitting still.

Cheers

Brett

Thanks guys! Giving me a bit of confidence, I was preparing for the worse.

Hopefully I will have it at my grandparents house now and there my parents can come turn it over a few times a month.

I will keep fuel in it so they can start it and maybe take it for a drive.

Was going to cancel the rego but will just leave it so they can drive it and move it if they need to.

I changed the oil today so it's fresh.

Also bought a good quality car cover.

I also have some stock rims and tyres so will just have it sitting on them.

Thanks for the help.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...