Jump to content
SAU Community

Snapped This, Now What

32GTRB

By 32GTRB,
in Engines & Forced Induction

 Share

Recommended Posts

32GTRB Proficient

32GTRB

Posted
Posted

Snapped the little adapter on my front turbo yesterday trying to bolt on a new twin turbo pipe. Ive glued it back together using epoxy but not sure if itll hold given the temps the compressor outlet might reach.

Anyone have a spare they want to offload or know where I can get a replacement (fleabay doesnt have), or anyone think the epoxy would hold? Im booked in for a retune next week but dont want any issues on the day :S

post-24058-14268331659283_thumb.jpg

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/454946-snapped-this-now-what/
Share on other sites
XRATED Veteran

XRATED

Posted
Posted

that's a whole lot of wrong going on up there....

The part would be available new or secondhand... new, try Kudos Motorsport... 2nd hand, try any import wrecker.

... funnily enough, gaskets are available too.

STOP USING FKN GASKET MAKER GOOP AND POXY FKN GLUE!!!

or sell your GTR cheap to someone who will appreciate it.

Cheers

J.

  • Like 1
32GTRB Proficient

32GTRB

Posted
  • Author
Posted

the pics above only show the goo, I was however using it with the gasket (the stuff smudged everywhere when I was pulling off the pipe).

dont think silicone is heat resistant enough to withstand the temps the turbo outlet would experience

GTSBoy Grand Master

GTSBoy

Posted
Posted

I hope that the silicone you used was oxygen sensor safe stuff.

The other thing is......a gasket on those surfaces would not likely need ANY sealant, and if I was to use sealant I wouldn't use silicone. There are many proper gasket selants out there, all of them 100x better than silicone.

breaker1845 Community Regular

breaker1845

Posted
Posted

Exactly, I hate using silicone sealant with gaskets so I use some different products that are much better and safe for oxygen sensors.

There is silicone products that is heat resistant up to almost 300 degrees which is plenty but in my opinion there are better sealants out there with much less mess.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...