Jump to content
SAU Community

Wax Or Sealant?

colourclassic
 Share

Recommended Posts

PM-R33 Grand Master

PM-R33

Posted
Posted

Hmmm applying a sealant over a wax is the exact opposite of what you are meant to do.....

With stacking, you always put the most durable product as your base and least durable as your top. Sealants also require a squeaky clean surface to bond to, this is why you are meant to always do an IPA wipe down of the surface before applying. So having a sealant try to bond to a Carnauba, Montan or Beeswax based wax normally doesn't go to well.

I personally haven't played with the Zaino stuff (but I am aware of their range) and the ZCS is meant to be the same as what Nanolex Spray Sealant is which I have plenty of experience in.

Very strange...

PM-R33 Grand Master

PM-R33

Posted
Posted

To get technical Modesta is a coating, not a sealant :)

Modesta is the same patented Japanese technology as what we do under the Gyeon range. Extremely good stuff that lasts for years.

This is my write up on the Gyeon Mohs + system but basically applies the same to Modesta BC-03 :) I've been thinking of offering Modesta as well just in case some people prefer one over the other.

www.attention-to-detail.com.au/what-are-gyeon-quartz-cloth-coatings

PM-R33 Grand Master

PM-R33

Posted
Posted

I believe so depending on what you want :)

It depends what is important to you I guess. The main benefit is the scratch resistance since that can't be reproduced with anything else. So in black cars swirl marks are always going to happen unless you are extremely careful with how you wash your car (most of the general public aren't but obviously on a car enthusiast forum like this a large majority are fussy about their car). The added hardness from the coating makes swirl marks nearly a thing of the past as long as you are a little bit smart with washing.

For a person that absolutely loves detailing cars and wants to be in the garage every few months all day long, then using high end waxes and such is fun and rewarding so a coating might not be necessary as you probably aren't getting the full benefits.

With me, I have a black 2014 Mazda 3 SP25 that my partner uses as a daily and isn't taken care of as much as it should, so for this I did a Mohs+ coating and it is fantastic for it since I know it is completely protected, easy to keep looking good and I don't need to clean it as often.

For my M3 I barely drive it and always try keeping it looking as best as I can. I like trying new products that suppliers send me and always do test panels to see how product A goes against product B. I'm extremely fussy with how I wash it and it is dark grey so for my car I like using waxes/sealants. If I didn't have the Mazda as well, I probably would have done a coating but this way I can show customers both vehicles if they want to see real world differences.

Check out her black Mazda 3 here: www.attention-to-detail.com.au/project-gallery/mazda3paintcorrection

The gloss and depth I got out of that was simply breathtaking but took my a week to do.

Either way I always recommend a coating to a customer because it is so different to waxes and sealants and is true modern day technology. Understandably the cost of $600-$800 that I charge might not be for every ones budget, but I still think it is a bargain given what it does.

  • Like 1
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
    • BOLGE
      R34 Plug Identification

      By BOLGE · Posted

      legend thanks mate !
    • fatz
      Neil's R33 Gts-t Build

      By fatz · Posted

      Skidz
    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
×
×
  • Create New...