Jump to content
SAU Community

Wax Or Sealant?

colourclassic
 Share

Recommended Posts

PM-R33 Grand Master

PM-R33

Posted
Posted

Hmmm applying a sealant over a wax is the exact opposite of what you are meant to do.....

With stacking, you always put the most durable product as your base and least durable as your top. Sealants also require a squeaky clean surface to bond to, this is why you are meant to always do an IPA wipe down of the surface before applying. So having a sealant try to bond to a Carnauba, Montan or Beeswax based wax normally doesn't go to well.

I personally haven't played with the Zaino stuff (but I am aware of their range) and the ZCS is meant to be the same as what Nanolex Spray Sealant is which I have plenty of experience in.

Very strange...

PM-R33 Grand Master

PM-R33

Posted
Posted

To get technical Modesta is a coating, not a sealant :)

Modesta is the same patented Japanese technology as what we do under the Gyeon range. Extremely good stuff that lasts for years.

This is my write up on the Gyeon Mohs + system but basically applies the same to Modesta BC-03 :) I've been thinking of offering Modesta as well just in case some people prefer one over the other.

www.attention-to-detail.com.au/what-are-gyeon-quartz-cloth-coatings

PM-R33 Grand Master

PM-R33

Posted
Posted

I believe so depending on what you want :)

It depends what is important to you I guess. The main benefit is the scratch resistance since that can't be reproduced with anything else. So in black cars swirl marks are always going to happen unless you are extremely careful with how you wash your car (most of the general public aren't but obviously on a car enthusiast forum like this a large majority are fussy about their car). The added hardness from the coating makes swirl marks nearly a thing of the past as long as you are a little bit smart with washing.

For a person that absolutely loves detailing cars and wants to be in the garage every few months all day long, then using high end waxes and such is fun and rewarding so a coating might not be necessary as you probably aren't getting the full benefits.

With me, I have a black 2014 Mazda 3 SP25 that my partner uses as a daily and isn't taken care of as much as it should, so for this I did a Mohs+ coating and it is fantastic for it since I know it is completely protected, easy to keep looking good and I don't need to clean it as often.

For my M3 I barely drive it and always try keeping it looking as best as I can. I like trying new products that suppliers send me and always do test panels to see how product A goes against product B. I'm extremely fussy with how I wash it and it is dark grey so for my car I like using waxes/sealants. If I didn't have the Mazda as well, I probably would have done a coating but this way I can show customers both vehicles if they want to see real world differences.

Check out her black Mazda 3 here: www.attention-to-detail.com.au/project-gallery/mazda3paintcorrection

The gloss and depth I got out of that was simply breathtaking but took my a week to do.

Either way I always recommend a coating to a customer because it is so different to waxes and sealants and is true modern day technology. Understandably the cost of $600-$800 that I charge might not be for every ones budget, but I still think it is a bargain given what it does.

  • Like 1
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...