Jump to content
SAU Community

S A U - N S W: April Monthly Meet - Sunday Brunch, Furious 7 Movie & Gtr N1 Showcase!


Recommended Posts

Great meet today guys!

Thanks for organising Raj, fantastic effort and cruise. Everyone well behaved.

So glad I could make it to a social event, it's been too long with family and work stuff.

  • Like 1

First social event I made it too, nice to meet everyone! I couldn't stay for the movie but definitely need to head back to the bunker, the chick schnitzels looked pretty damn epic!

Had a few car issues on the way home so probably a good thing that didn't happen on the way to katoomba, hope to be at the next one.

  • Like 2

Thanks for organising Raj. Great day out. Sorry I missed the M4 meetup, I came straight from Terrey Hills and made it out of there faster than expected.

  • Like 2

Thank you all for coming to today's meet. Really appreciate it.

Chris, it started to rain just as I entered the driveway lol. Wont ever forget today - the day I drove a R34 GTR N1. Whooo!

Haha the car gods were indeed watching over you ay!

  • Like 1

STAGEA INVASION!!!!



16922998277_649612d6db_b.jpg

16922997597_d44d133660_b.jpg



16944194399_c5b471e504_b.jpg



16942610138_2e2f76543c_b.jpg

17129744301_423f4f3331_b.jpg

Great shots Ciaron; thanks mate!

Edit; I've shared these in a couple of Stagea Pages Ciaron, with credit to you of course.
Is that ok?

  • Like 3



  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...