Jump to content
SAU Community

Recommended Posts

Doesn't sound that bad Pete. The new dump will improve response, something you should really feel driving it rather than see on a dyno. Obviously the turbo was selected for response so that's why its running out of puff up top on a 3.2 and why the bigger dump isnt making much difference in the top end. Don't stress about it. As long as all the tuning is done right so you don't have the previous issues. Don't worry about e85 either, it would be a head f**k for a daily seeing that its becoming more scarce. See how you go but I recon it should be exactly what you want. Hope so anyway. :)

I am not sure how it works but the PT6262 CEA is rated at over 700HP and this is only running around 520HP @ 22psi so I do not think it is running out of puff, might need some boost to get the 6262 going harder , do I need more boost, I do not think so,but it would be interesting to see how it goes :)

But as you said, it will be all I want if the dump gives a little more response and it only matters when you are driving it.

Why didn't that embed......

What's the response of car like, or not driving it yet?

Not yet, should be sometime this week, if the leak has been sorted, should know tomorrow and maybe it will be tuned then ?

Based on others, 6266 is better for higher revs on a 3.2. Your 62 rear is probably restricting exhaust gas flow. Even if you increase boost its a scenario of diminishing returns comparing to a bigger turbo, but the trade off would be low end. But the 3.2 will look after that to a point.

  • Like 1

Your probably around the 560-570hp mark ATM Pete

700 is absolute best case scenario

ATM it is about ,615HP ish crank. well I think 386 awkw is around 520whp

I know I keep saying this, but I still want it to go earlier , so I will wait and see what happens when I give it a run :)

I'm probably missing something;

Ran car at full power (identical set up?) and noticed less power than before...casual observation, nothing more to add?

Turned boost down (from 22 psi) and then it doesn't misfire...is that being offered as the solution to the misfire?

Put other cams in that were found to be better, then took them out again...?

  • Like 2

Based on others, 6266 is better for higher revs on a 3.2. Your 62 rear is probably restricting exhaust gas flow. Even if you increase boost its a scenario of diminishing returns comparing to a bigger turbo, but the trade off would be low end. But the 3.2 will look after that to a point.

I know this will sound dumb to you blokes that have driven these cars for yonks, but getting used of a car that revs so high is very strange.

This car was limited at 10000rpm, or maybe no limiter,the first time I went over 10000rpm because I was too slow to change up, it went nuts from 6000rpm , hit 10,000 in a flash and I shit myself LOL

I'm probably missing something;

Ran car at full power (identical set up?) and noticed less power than before...casual observation, nothing more to add?

Turned boost down (from 22 psi) and then it doesn't misfire...is that being offered as the solution to the misfire?

Put other cams in that were found to be better, then took them out again...?

Lets see how it goes, only a few days to wait until I get my arse in the car, that is the only test :)

All jokes aside, what's the obsession with turning them so damn hard? Is it the noise of it screaming it's head off?

Mainly because it would not go over 6500rpm, there was no need to do it. Shit load of fun @5500rpm :)

Mainly because it would not go over 6500rpm, there was no need to do it. Shit load of fun @5500rpm :)

Not talking about your setup. I'm talking about turning the to 10,000 rpm and beyond for a car that's driven on the street. Is 8000 rpm not enough?

All jokes aside, what's the obsession with turning them so damn hard? Is it the noise of it screaming it's head off?

All of the above. He he. Love it.

Seeing you're such a fan of 26s, I think you will like to know I am putting a t04z on mine shortly. More lag, just the way you like it, he he

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...