Jump to content
SAU Community

Recommended Posts

13 minutes ago, Manne said:

That's what is sounds like.

I'm not sure if my car can handle a spirited drive in the hills right now, we'll see what happens on the day.

Bike?

I could do, but I'm not sure if Riding in the hills at night is a smart idea or not, Seen too many accidents.


Yer nah night a tight roads possible gumnuts.
Better in car. She handle it its a drive not a track day [emoji39]
8 hours ago, Hank Scorpio said:

So is the plan to meet at the Tavern and then do a short drive after the meal?

Yes meet at Tavern

Meet each other if its a big turn out then stand etc..

But if reasonable secure a table and have a seat (most likely outside) and smash some pizza.

After that a drive would be nice.

30mins 

Or  

1hr.

Up to you guys but i have to post by Friday on the event page. 

  • Like 1
Yes meet at Tavern
Meet each other if its a big turn out then stand etc..
But if reasonable secure a table and have a seat (most likely outside) and smash some pizza.
After that a drive would be nice.
30mins 
Or  
1hr.
Up to you guys but i have to post by Friday on the event page. 


Sounds like a great idea. Meet at Tavern, 30 minute drive afterwards to a meeting point, say good night and head home [emoji106]
  • Like 3

Ok so i think i found what i want but there is no pictures or diagrams of where that part belongs On the website.
So i thought if i go to nissan give him my vin or part number he have a look so.
.
He said only OEM parts he can find that belongs to the car he than said the part number should not start with a letter so what i gave him was no good.
He also said dealer option wound not come up....?

1486004404099.thumb.jpg.3f602892f78443e0
Dose that website if i contact them do you think they got the digram where it belongs.

No idea, however lots of genuine Nissan part numbers start with a 'K'.

http://nissan.epc-data.com/skyline/bcnr33/3940-rb26dett/misc/F80/

'6935' seems to refer to a "console finisher", I reckon you're about on the money mate.

  • Like 1
you buying cf dash pieces for the 33?  WHere from ?
Have you tried Robsons in Singapore - there kit / work is amazing.
Im keen as well - can get 2 sets perhaps?
Dan

Ok yer ill have a look but im more keen on oem or nismo.
makes the gtr shine with more pride!
Would be more annoying when driving and looking at it think only if it was made by nismo. Haha im loosing my mind [emoji38]



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...