Jump to content
SAU Community

Recommended Posts

30 lol

A young man in his prime:-) servicing anything he can get a spanner on. How goes the Nissan front end? Mate Dave came over, yep he reconds better tyres like you guys said, he freaked out on how hard the Nissan is pulling compared to when we test drove it. he crashed the 1970 boss351 mustang. First prang in 32 yrs of driving. Locked it up in the wet not paying attention reefed it sideways and back end quater hit a Hyundai Excel. :'( never seen him so humble.) my fault. He reconds shannons were awesome to deal with. Insured for 40.000.
  • Like 1

Just loaded vid clips onto my new ute DVD player and found clips from 13-14 years ago when I was younger n sillier and first started downloading . Music really brings memories back so easily.

2 hours ago, Beyond Blue R33 said:


A young man in his prime:-) servicing anything he can get a spanner on. How goes the Nissan front end? Mate Dave came over, yep he reconds better tyres like you guys said, he freaked out on how hard the Nissan is pulling compared to when we test drove it. he crashed the 1970 boss351 mustang. First prang in 32 yrs of driving. Locked it up in the wet not paying attention reefed it sideways and back end quater hit a Hyundai Excel. :'( never seen him so humble.) my fault. He reconds shannons were awesome to deal with. Insured for 40.000.

Ah bugger, whats happening with the mustang? Skylines looking a little sad, no guards, bonnet and skirts. Most of its on the roof lol gonna start drilling the welds out this weekend. Not gonna weld on the new one on, gonna have it bolt on so i can remove it when for easyer engine access ?

20170914_203819.jpg

  • Like 2
Ah bugger, whats happening with the mustang? Skylines looking a little sad, no guards, bonnet and skirts. Most of its on the roof lol gonna start drilling the welds out this weekend. Not gonna weld on the new one on, gonna have it bolt on so i can remove it when for easyer engine access [emoji106]
20170914_203819.thumb.jpg.51ce277e8b61a66a506bb15d8c67b971.jpg

Paying the help in scooby snacks I see. Cheap labour. Mustang is in panel beaters.
  • Like 1
9 hours ago, Beyond Blue R33 said:


Paying the help in scooby snacks I see. Cheap labour. Mustang is in panel beaters.

The opposite, they hinder progress trying to sit on my lap and lick my face! 

  • Like 2

What did the poisoning?

Jack has changed tack and wants to be a police officer again. Plotted a 12km run to the lake and back. I Was in front for about 9kms then died in the ass. Tried to pick it up when he passed me but ended up walking home. [emoji70] shins and calves are killing me. Eli? New coaching:-/



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...