Jump to content
SAU Community

Recommended Posts

Has anyone replaced their under bonnet mat??? if so what did you use/where did you source one???

I' have been looking but generally running around in circles and getting nowhere.

And for those that must lose weight by all means possible - apologies but I don't....so I'd really like to source a new or near new under bonnet mat.

Thanks in advance!!!

Link to comment
https://www.sau.com.au/forums/topic/457416-under-bonnet-mat/
Share on other sites

They do pop out but it is best to use a trim removal tool.

Go down to supercheap and spend $10 bucks and get a pack of 4 or so.

They come in handy removing trim clips.

Age of clips and angle when you lever them out and they break

  • Like 1

Anyone able to share the part number for this item please?

If they are vehicle/model specific, I am after one for a BNR34 V-spec II

I always assumed it was specific to the carbon bonnet, to protect it from heat... seems not?

  • 3 weeks later...

No, I didn't go ahead with it..........price was $126USD but freight/postage was $800USD. I asked them to double check the postage but never ever got any reply or help.

They are a peculiar company to deal with in some respects...I had trouble communicating.

I run my "line without the bonnet mat, it had a tear in it and had some oil soak from the previous owner. Looks neater and I don't have any issues with paint fade. If you don't mind doing a bit of cutting and measuring, then maybe you can try out Dynamat or this :

http://www.thermotec.com/products/13500-adhesive-backed-heat-barrier.html

Thanks nanogrip, I was looking at that sort of product but baulked at it becuase it would be a real bitch to get off if you ever had to replace it or repair a dent etc. [[which I just had to recently do when two acorn nut looking things fell out of a tree and put a couple of small dents in my bonnet - paintless dent removal and $50 later fixed it though, BUT they had to remove my mat to access them from underneath.

Maybe I should think about organising a group buy???

Hi all, I've started a newbie group buy. Its more an expression of interest at the moment but will happen if we get the numbers!!!

So if you want one then please put your name on the list. I'll leave it open for say 4 weeks tthen if we get enough numbers I'll go to the next step.

http://www.sau.com.au/forums/topic/458455-under-bonnet-mats/

  • 1 month later...

Just to let people know we are going ahead with this, looking for a few more numbers to get a better price $251 vs $239. If we get another 2-3 people we are sure to do it.

I'm reviving my old thread to let people who haven't yet seen our group buy know - just in case. Sorry I asked about R32 ones and they are now out of production, so only R33 and R34.

That's not to say that they won't ever make the R32 ones again, just not for now.

And yeah, it took longer than 4 weeks.............

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...