Jump to content
SAU Community

Recommended Posts

Hi All,

i have a 19incher wheels and running kumho Le sport KU39 245/35/19, i find that every 5k kms i have to realign my tyres as around 5000 kms it start to make that out of alignment noise.

Is this common?

should i increase my profile to 40series next time to lessen the frequency of alignment?

thanks

JT

Link to comment
https://www.sau.com.au/forums/topic/457982-wheelstyre-noise/
Share on other sites

I had no idea you could hear when your tyres were out of alignment.

And sure. Run some 40 series tyres. Because, you know, that would be way closer to rolling diameter of stock wheels. Even the current profile is good and I bet your speedo isn't off or anything.

I'd say you're hearing the noise because it's pretty average rubber you have there. Once I got rid of my Kumho KU31s and replaced them with Michelin Pilot Sport 3 tyres, no more screeching around bends.

ok something to think about next time around..i though the le sports were pretty high end of the kumhos..

ok something to think about next time around..i though the le sports were pretty high end of the kumhos..

In my experience and very humble electrical engineer's opinion (i.e. I have no expertise in the field of tyres), Kumho don't produce anything high end when it comes to road tyres.

The KU36s I had were one of the best tyres I have used for grip and feedback, pitty they are insanely noisy. Not suitable for a daily IMHO, unless you have a car with a lot of sound insulation.

I have had KU19s too, and they were quite poor all round.

Hi Ben,

can you be a bit more specific? do you think its my driving style or the amount of times i hit pott holes? lolz

or could my cheap rims could be causing this? i have kings malice

If the alignment is changing that's the cars fault, not the tyres.

In my experience and very humble electrical engineer's opinion (i.e. I have no expertise in the field of tyres), Kumho don't produce anything high end when it comes to road tyres.

ok apart from michelins and pirelli's do you have other experience with other brands that are a little cheaper than them two? hehe

The KU36s I had were one of the best tyres I have used for grip and feedback, pitty they are insanely noisy. Not suitable for a daily IMHO, unless you have a car with a lot of sound insulation.

I have had KU19s too, and they were quite poor all round.

He has KU39 not KU36. Kumho aren't the 'best', they are a good low-mid-range tyre. They aren't that quite either. My Subaru came with KU22 and they were quite noisy, changed to Momo M3, quieter and grippier, but can go more quiet (will next round of tyres, gonna get Michelin).

OP, you may have some worn bushes?

He has KU39 not KU36. Kumho aren't the 'best', they are a good low-mid-range tyre. They aren't that quite either. My Subaru came with KU22 and they were quite noisy, changed to Momo M3, quieter and grippier, but can go more quiet (will next round of tyres, gonna get Michelin).

OP, you may have some worn bushes?

Ok bought the car with 35k kms. i've done 75k now. tyres and wheels have done 16k kms. so you think time to go take it to pedders?

:) I wouldn't take box trailer to pedders.. But maybe some franchises are better than others..

I have had many good experiences with the local fulcrum suspension outlet, but I am not sure if they are in all locations.

As for the KU36, I know the op had 39s, I was just pointing out they do make a good tyre, if you can ignore the noise. A friend at work uses them on his turbo rx3 track car.. Where noise isn't exactly a problem.

But their 'mid range' tyres are quite ordinary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...