Jump to content
SAU Community

Recommended Posts

When I got my RB74 pads, they were rather quiet. After several months though, the right front brakes started to get a little noisy. When it got to the stage where it would squeal on every slowdown, I decided to see if I could fix it (well, I put it off for a few weeks because I'm a lazy bastard). Here's the brief rundown on how I did it.

1. Buy some red gooey anti-squeal stuff from my local spares shop.

2. Buy 1-2 sheets of 80 grit emery paper from the same shop (around $1.25 a sheet)

3. Jack car up, remove offending wheel.

4. Remove clips and springs from pads.

5. Remove pads from caliper.

6. Sand back the pads on the emery paper until the glazed surface is roughened up. There may be some scoring marks left on the pads, it's not essential to get rid of every little groove.

6a. If your discs are badly scored, get them machined. Maybe you should figure out whether or not they need machining before you sand the pads back.

7. If the discs are fine and you can be bothered, give the discs a quick once-over with the emery cloth. It's pretty difficult to make even a light indent in the discs though, so don't worry too much.

8. Put red gooey stuff all between each layer of pad and backing plate, as well as on the back of the plate that sits on the caliper piston.

9. Put pads back into the caliper after the red gooey stuff goes tacky.

10. Bend the anti-squeal spring in the opposite direction a bit, to give it more tension for when it's in place.

11. Put spring and clips back in, put wheel back on, etc etc.

12. Test everything.

13. If you crash your car for any reason, don't blame me (disclaimer).

It's weird how only my right front brake started squealing. The left front one has remained quiet all this time so I didn't bother doing that side. I only fix what's broken :)

  • 1 year later...

I had bendix ultimates and they squeeled like a beatch and drove me nuts. I went and bought some of that anti squeel spray but it didn't help me at all ( i still had anti squeel shimmy things in there though). When I changed brake pads I got LUCAS ones put in, and they have not made a single noise ever!

I'm so impressed with these pads, they stop beautifully, don't leave my rims as filthy as the bendix ones, and they don't squeek!

So there's my advice, use the Lucas pads! (I've heard the RB ones are a bit squeeky too!)

  • 1 month later...

its mainly just the dust that makes the pads squeal after awhile. i have ferrodos that are hell dusty. i just got some anti-squeal from my work, cleaned up the discs and pads, put it on the back of the pad, includin the spring and it has never sqeualed again.

I've had Ultimates, from readings I was expecting them to squeel so I bought my self a tube of PBR anti-squeal adhesive, slapped it every where over the back of the disk and antisqueel shims.

They never squeeled so it worked. :huh:

The car was only driven on the street and never saw anyhard braking.

  • 1 year later...

my ultimates used to squeel as if they were getting molested or something..

i tried the paste stuff which didnt do anything at all..

the spray worked realy well tho ;) fixed it up 100%

alltho i have a feeling the spray doesnt work for all that long ??

well the spray lasted for about 50km of driving..... :(

my ultimates used to squeel as if they were getting molested or something..

i tried the paste stuff which didnt do anything at all..

the spray worked realy well tho :) fixed it up 100%

alltho i have a feeling the spray doesnt work for all that long ??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not really, but the heater box is pretty simple mechanically....if the door is one way the air bypasses the heater core and if it is the other way it goes through it for warm air.  If you are sure the actuator you moved manually is for the heater mix (there would also be one for output air direction) then I'd take the heater box out and see what is happening (you'll have to regass and re-coolant the systems afterwards) BTW pp724 onwards from the GTR workshop manual cover the system in good detail, it is probably worth checking. I think the IAT sensor might be a problem electrically for getting cold (if you got 24 error code not -24 it thinks the incoming air is -50c) and it covers how to test the sensor (although most likely it is either not plugged in or a wire is damaged)
    • Use the GKTech subframe bush and bring your subframe 10mm closer to the chassis. You'll need to fix an exhaust hanger to suit. One of the best mods I've done.
    • You'd really have to pull it apart further to know, it least you can be confident that the one heading to the back is not connected any more. There was once a ground on the shifter seal mount too, your head unit issue could be that simple
    • Perfect, I'll get to it this winter then at the same time as I weld on my anti squat kit. 
    • Alright so my 32 only has one temperature no matter what degree you set it to. I’ve tried disconnecting the servo motor arm and moving it either direction and got no change. I’ve fixed the leak in my AC and re charged it and with it on and clutch engaged it still blows hot even though the low pressure pipe going to the firewall is ice cold. Both heater core hoses are hot while running as well. Diagnostic code showed 24 for intake air temperature sensor. Anybody got any ideas?
×
×
  • Create New...