Jump to content
SAU Community

Recommended Posts

Hi guys, been searching everywhere for an answer but cant seem to find a pinpoint one so im hoping you guys can help.

Basically when i hit about 4.5-5 revs the car just seems to die in the ass and not want to go anywhere at flat foot but if i creepy up the revs at 1/2 throttle and then 3/4 throttle then flat foot it at higher revs it goes like a rocket but after giving it that little boot full the turbo seems to completely stop working and wont even spool up or flutter for ages unless it sits for awhile or car is turned off.

Now when im flat foot it just feels like its choking and struggles to move through the 4+ revs or even the lower revs when trying to accelerate a little quicker then normal.

also when putting the boost up to say 10-11 psi the turbo always spools but its like the ecu doesnt know what or how to handle this bit of extra boost and just wont go anywhere aswell.

hopefully i have described this decently enough to have you gurus tell me how to fix this issue, as it seems to be a trick to try and put into words how to describe whats happening lol.

specs- rb25det neo, all stock setup except for coilpacks which are probably less than a year old (splitfires), changed plugs less than 2 weeks ago.

car has only recently in the last couple weeks started having this issue and before that it was a fun and reliable car to thrash around.

cheers

Link to comment
https://www.sau.com.au/forums/topic/459280-33-rb25det-boost-problem/
Share on other sites

Search nazis should be shot, a bit like small dick punctuation nazis...

anyway back on subject, you changed plugs now have issues? Is that the only thing you've done? What's your air filter like? Fuel filter?

Air/fuel/spark [emoji6] check those first

Either put everything back to stock, or tune the car.

You can't just go bumping the boost up without tuning, it will run like balls and perhaps throw a turbine wheel. It will run even worse if you have a highflow turbo you don't know about.

Everything is back to stock, was just driving home from the gym and it seems once the turbo spools up to a certain point and I off the accelerator it just stops working.

Plugs were gapped correctly and I'm under the impression I'll need to go for a tune, was just seeing if anyone has any ideas. I'm very new to the forced induction life, lesrn from

Your mistakes I guess.

Cheers guys :)

Turn you boost down, colder weather means denser air. More "air" read by the AFM means a higher TP Load, and because it's a stock ECU and tune you're hitting cells where timing is absolutely retarded as fk.

Boost doesn't equal TP Load, you might be able to run 10/11 psi in summer or so but when it's cold you'll hit those cells running the same boost.

I suggest you turn down the boost.

Turn you boost down, colder weather means denser air. More "air" read by the AFM means a higher TP Load, and because it's a stock ECU and tune you're hitting cells where timing is absolutely retarded as fk.

Boost doesn't equal TP Load, you might be able to run 10/11 psi in summer or so but when it's cold you'll hit those cells running the same boost.

I suggest you turn down the boost.

Have turned boost back to normal but is still having issues

Sounds like your AFM has dry joint inside it then. Cut it open and solder the pins first, there is a how to on here somewhere.

A new Z32 AFM and a tune would likely fix it too.

Thanks dude, I had a feeling it might be the afm so I'll go sort out a z32. I appreciate the feedback

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...