Jump to content
SAU Community

Recommended Posts

Those new Yoki's are pretty spesh huh, I'm running the same size compound on mine now and I cannot wait to see if I can beat my 03G time :)

At Oran and Eastern Creek, 50's in M's are a second quicker - be prepared there a bit soggy compared to 285 Dz03's, Yoki's were a bit quicker, but easier on the bankcard! Soft compound seems great on R32 with less grunt, they get over it too quick on R33 - M's are the go for me.

Must say havent tried em in the wet yet, so will probably put the dunlops back on for that occasion, although on behaviour, I do have high expectations of the Yoki's with 50% plus tread in wet.

Check out vids on Skylines Australia > Automotive > Motorsport > Club Level Motorsport > In car videos

  • 1 month later...

Hey guys i've gone through most of this thread and updated a few of the times for the tracks and will continue to do so for this year as well.

If you have a laptime to be updated just shoot me a PM with the details and i'll make sure its done :D

First time out in the 32, running low boost.

SAU Nickname: Duncan1

Car Make and Model: R32 GTR V-Spec

Circuit Name: Queensland Raceway Sprint/Clubman

Lap time: 58.2 Sprint/1:01:1 Clubman

Date 6/10/09

Modifications: brakes/suspension/gear box/Nismo LSD

Engine: Forged 26/T04Z

Power: approx 330awkw on the day- [will run all 420awkw next time]

Suspension: Ohlins

Tyres: Re55's

Brakes: Alcon fronts, 365mm 2 piece rotors/ Brembo rear

Body weight: Stock/ full trim

Needed more neg camber/ Ok result for its first outing.

Ben would you mind adding these times..

thanks mate!

#####NEW UPDATE#####

SAU Nickname: Duncan1

Car Make and Model: R32 GTR V-Spec

Circuit Name: Queensland Raceway Sprint/Clubman

Lap time: 57.9 Sprint/1:00:9 Clubman

Date 11/02/10

Modifications: brakes/suspension/gear box/Nismo LSD

Engine: Forged 26/T04Z

Power: approx: 420 awkw

Suspension: Ohlins

Tyres: Re55's

Brakes: Alcon fronts, 365mm/ Brembo rear

Body weight: Stock/full Trim

almost time to lock the OP times unless there are people even slacker than me!

SAU Nickname: Duncan

Car Make and Model: R32 GTR V-Spec2 N1

Circuit Name: Oran Park

Lap time: 1.19.4568

Date 16/01/10 (last ever race meet)

Modifications: brakes/suspension/gear box/Nismo LSD

Engine: standard, 12psi boost

Power: 240ish awkw

Suspension: Bilstein, eibach springs

Tyres: Tiny little slicks (kumho front, falken rear) 235/40/17

Brakes: Porsche 4 spot front on standard rotors. standard rear

Body weight: 1500kg

http://www.natsoft.com.au/cgi-bin/results....01/2010.ORGP.R2

Hi,

Car is a Nissan 200sx

Oran Park Grand Prix

01:18.800 - S14a - 200kw - RE55

http://www.natsoft.com.au/cgi-bin/results..../2009.ORAN.S2.Y

Oran Park South

00:48.330 - S14a - 200kw - R888

http://www.natsoft.com.au/cgi-bin/results....006.ORAN.S2.I.Y

Wakefield Park

01:06.560 - S14a - 200kw - RE55

http://www.natsoft.com.au/cgi-bin/results..../2009.WAKE.S5.Y

Phillip Island

01:48.9590 - S14a - A050

http://www.natsoft.com.au/cgi-bin/results....2010.PHIL.S25.Y

Eastern Creek

01:49.690 - S14a - 200kw - R888

Don’t have a link as was so long ago

Hi,

Car is a Nissan 200sx

Oran Park Grand Prix

01:18.800 - S14a - 200kw - RE55

http://www.natsoft.com.au/cgi-bin/results..../2009.ORAN.S2.Y

Oran Park South

00:48.330 - S14a - 200kw - R888

http://www.natsoft.com.au/cgi-bin/results....006.ORAN.S2.I.Y

Wakefield Park

01:06.560 - S14a - 200kw - RE55

http://www.natsoft.com.au/cgi-bin/results..../2009.WAKE.S5.Y

Phillip Island

01:48.9590 - S14a - A050

http://www.natsoft.com.au/cgi-bin/results....2010.PHIL.S25.Y

Eastern Creek

01:49.690 - S14a - 200kw - R888

Don’t have a link as was so long ago

Nice PI time. How to you rate the 050's against the RE55's?

It's a little hard to tell as first time on PI but seemed to be quiet good, the wear was comparable to the re55's and didn't seem to suffer what I experienced with the R888's in tread block squirm. They do seem to have some tread block movement due to the design but it seems to be only minor that shows in the wear on the tyre when you are looking at them and not through the wheels.

The FR is nearly dead but apparently that is expected at PI and suffered from getting a bit too much pressure too quickly and I didn't bleed it off quick enough so wear in the centre of the tyre is higher.

Felt fast, stable at higher speeds and came on quiet a lot quicker then what I would experience with the RE55's. I didn't expect this and found myself getting stuck into it earlier and earlier then what I would normally.

Probably the best tyre I have tried but would like to see the results on a home track before singing its praises.

It's a little hard to tell as first time on PI but seemed to be quiet good, the wear was comparable to the re55's and didn't seem to suffer what I experienced with the R888's in tread block squirm. They do seem to have some tread block movement due to the design but it seems to be only minor that shows in the wear on the tyre when you are looking at them and not through the wheels.

The FR is nearly dead but apparently that is expected at PI and suffered from getting a bit too much pressure too quickly and I didn't bleed it off quick enough so wear in the centre of the tyre is higher.

Felt fast, stable at higher speeds and came on quiet a lot quicker then what I would experience with the RE55's. I didn't expect this and found myself getting stuck into it earlier and earlier then what I would normally.

Probably the best tyre I have tried but would like to see the results on a home track before singing its praises.

Thanks for that. RE55's are getting very hard to get at the moment. May try the 050's next to see how they compare.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...