Jump to content
SAU Community

Recommended Posts

Yes, was distracted, missed a key step, hope I haven't junked the motor.

rb30 is an interference motor.

Was torqueing down head, had the no.1 cylinder set to TDC, forgot to clock the cam pin to the top.

Instead of the pin sitting at 12 o'clock, was sitting at roughly 3 oclock.

3 oclock puts the valve on the piston.

was able to rotate the cam backwards to 12 oclock but there didn't seem to be much movement past where it was sitting originally in the clockwise direction.

because the piston was at TDC, the valve wouldn't have pushed it down.

how likely is it that I've bent a valve?

Yeah they don't take much to bend. Put the belt on (timed correctly obviously) and turn the motor over. Check to see if the valve is fully seating once it comes off the cam and is closing (watch the spring to see how smoothly it closes the valve). If it either grabs then releases or just doesn't seat at all them I'mm sorry to say but get that head off again!

Yeah they don't take much to bend. Put the belt on (timed correctly obviously) and turn the motor over. Check to see if the valve is fully seating once it comes off the cam and is closing (watch the spring to see how smoothly it closes the valve). If it either grabs then releases or just doesn't seat at all them I'mm sorry to say but get that head off again!

Is it possible to see whether the valve is seating with the rocker cover off (but the head still bolted down)?

If you have literally just bolted the head down, why not take it back off and look

Well, didn't want to throw away a set of stretch bolts if there was some way of telling if it was ok without removing the head, but it may come to that...

Is it possible to see whether the valve is seating with the rocker cover off (but the head still bolted down)?

Pretty much. You'll be able to see the valves through the ports but mainly you will be able to see the difference in height of the valve tip/spring when the compared to those next to it. If it's stuck open it will be sitting lower than the other valves when they're closed. If it's hard to turn over when the lifter starts to climb the lobe (on the problem cylinder) then the valve could be bent but straight enough to close but then grabbing in the guide when it tries to open.

Depending on what you have available pressurising the cylinder through the spark plug hole will show up a bent valve easily. As would a comp test

yep, going to try to get a hold of a leakdown tester this weekend.

Ordinarily would not care about $46 for a set of bolts, but they won't be delivered by this weekend and I need the car running ASAP, was hoping to get it installed back in the car over the long weekend. If I can get a leakdown test done on Sunday I'll either be able to go ahead with installation, or buy bolts and valves as required on Tuesday...

Thanks for all the responses!

  • 2 weeks later...

UPDATE: as I suspected I bent one of the valves, it's only on 5 now.

There's a reasonably priced reco head on Ebay, but it's for a VL Commodore rb30e, not a skyline.

I heard they had different cams - will this be a problem? Also will it bolt up and run okay with the r31?

Just swap your cams into the new head if you're worried they'll be different (I don't imagine they'll be different enough to be a problem). They're hydraulic lifters so you don't need to worry about clearances or anything, just whack them in and off you go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...