Jump to content
SAU Community

Installing Oil Cooler, Location Problem

sean3444
 Share

Recommended Posts

sean3444 Newbie

sean3444

Posted
Posted

Hey guys, installing a oil cooler and relocation kit

Looking at mounting the cooler in front of the radiatorbut there are 2 lines(backed on itself )in the way.

Ive traced one end back to the power steering fluid resovoir but unsure of where the other side ends, i assume its some sort ot cooler ( pictures attached )

So my question is can i get a relocation kit for this and any other preferable mounting positiongs for the cooler, i cant see where the mount is possible behind the front bar left or right side.

Cheers, kind regards

post-142910-0-27139200-1459226878_thumb.jpeg

post-142910-0-85997600-1459226929_thumb.jpeg

post-142910-0-84933500-1459226952_thumb.jpeg

sean3444 Newbie

sean3444

Posted
  • Author
Posted

Have you um checked anyone else's setups?

Majority of setups are where these lines are or under the front bar infront of the air ducts on the left or right side

Does anyone know if you can get a relocation kit for the power steering lines as i am unable to find

Cheers

V28VX37 Veteran

V28VX37

Posted
Posted

Yes it's for R33 but pretty much all the possible oil cooler location options are documented in this thread: http://www.sau.com.au/forums/topic/79130-r33-oil-cooler-installation/

I read it top to bottom before installing mine, great info.

Ideally you'd want your oil cooler under left or right headlight behind the front bar so it's not in line with intercooler, A/C core and radiator.

However depending on the size of your oil cooler core this may not be possible, especially presuming you have IC piping running on both sides since it's a GT-R.

sean3444 Newbie

sean3444

Posted
  • Author
Posted

Yes it's for R33 but pretty much all the possible oil cooler location options are documented in this thread: http://www.sau.com.au/forums/topic/79130-r33-oil-cooler-installation/

I read it top to bottom before installing mine, great info.

Ideally you'd want your oil cooler under left or right headlight behind the front bar so it's not in line with intercooler, A/C core and radiator.

However depending on the size of your oil cooler core this may not be possible, especially presuming you have IC piping running on both sides since it's a GT-R.

hey mate, yeah isnt a whole lot of room with the IC piping, cheers for that link i had a read, and ill have another look for potential spots tommorow.

thinking of relocating the power steering lines to fit the it infront of the ac core. not ideal spot but im not sure it will fit under the head lights.

regards

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...