Jump to content
SAU Community

Recommended Posts

Possibly having an option to live and work in Japan for 18mths and off course would like to bring a car back as a personal import.

Racking my brains on what would be a good car to bring back, off course things like BNR34 are an option but would like to see if anyone has any better ideas.

Budget of under/around 5,000,000 yen.

Link to comment
https://www.sau.com.au/forums/topic/463996-personal-import-what-to-go-for/
Share on other sites

Classics Present and Future

* Honda NSX

* Honda NSX-R

* R32 GTR N1 (V-Spec or non)

* R32 GTR Nismo

* R33 GTR N1

* R33 GTR 400R

* R34 GTR N1 (V-Spec or V-Spec II)

* R34 GTR V-Spec II Nur

* R34 GTR M-Spec Nur

* R34 GTR Omori variants

The private treaty cars that haven't been graded need to be checked out thoroughly for rust as well as other essentials.

  • Like 1

Love the list Terry but most would be well above 5mil, especially something like NSX Type R.

Desmosedici is a good one, I could get that and wifee could get a car to get around while there.

Edited by rehab2010

Love the rotors - been actually looking at a RX-7 Spirit R Type A......because I'm predictable.

Actually, something out of left field, a new Civic Type R.

post-62747-0-54059900-1459764715_thumb.jpg

Edited by rehab2010

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...